Nissan Qashqai (2007-2010). Manual — part 1933
SN
BUZZER DRIVE SIGNAL CIRCUIT
SN-9
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BUZZER DRIVE SIGNAL CIRCUIT
Description
INFOID:0000000000935757
The sonar control unit outputs the buzzer drive signal when the rear sonar detects the obstacle.
Diagnosis Procedure
INFOID:0000000000935759
1.
CHECK HARNESS BUZZER CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sonar control unit connector and buzzer connector.
3.
Check continuity between sonar control unit harness connector terminals 2, 6 and buzzer harness con-
nector terminals 2, 1.
4.
Check continuity between sonar control unit harness connector terminal 2 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK BUZZER DRIVE SIGNAL
1.
Connect sonar control unit connector and buzzer connector.
2.
Bring an obstacle near to sound the buzzer.
3.
Check signal between sonar control unit harness connector terminals 2 and 6.
Is the inspection result normal?
YES
>> Replace buzzer.
NO
>> Replace sonar control unit.
2 – 2
: Continuity should exist.
6 – 1
: Continuity should exist.
2 – Ground
: Continuity should not exist.
2 – 6
Waveform period changes
due to the distance to an ob-
stacle.
JPNIA0232ZZ
SN-10
< COMPONENT DIAGNOSIS >
SENSOR SIGNAL CIRCUIT
SENSOR SIGNAL CIRCUIT
Description
INFOID:0000000000936324
The sensor detects the distance to obstacles and outputs the signal to the sonar control unit.
Diagnosis Procedure
INFOID:0000000000936326
1.
CHECK SENSOR POWER SUPPLY AND GROUND CIRCUIT
Check sensor power supply and ground circuit. Refer to
Is inspection result normal?
YES
>> GO TO 2.
NO
>> Repair malfunctioning parts.
2.
CHECK HARNESS SENSOR SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sonar control unit connector and each sensor connector.
3.
Check continuity between sonar control unit harness connector terminals 13, 14, 15, 16 and each sensor
harness connector terminal 2.
4.
Check continuity between sonar control unit harness connector terminals 13, 14, 15, 16 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK SENSOR SIGNAL
1.
Connect sonar control unit connector and each sensor connector.
2.
Turn ignition switch ON.
3.
Shift the shift position to “R” position.
4.
Check signal between sonar control unit harness connector terminals 13, 14, 15, 16 and Ground.
Is the inspection result normal?
YES
>> Replace sonar control unit.
NO
>> Replace malfunctioning sensor.
13 – 2
: Continuity should exist.
14 – 2
: Continuity should exist.
15 – 2
: Continuity should exist.
16 – 2
: Continuity should exist.
13 – Ground
: Continuity should not exist.
14 – Ground
: Continuity should not exist.
15 – Ground
: Continuity should not exist.
16 – Ground
: Continuity should not exist.
13 – Ground
14 – Ground
15 – Ground
16 – Ground
JPNIA0233ZZ
SN
SONAR CONTROL UNIT
SN-11
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
ECU DIAGNOSIS
SONAR CONTROL UNIT
Reference Value
INFOID:0000000000935763
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA0231ZZ
Terminal No.
(Wire color)
Description
Condition
Reference value
(Approx.)
+
–
Signal name
Input/
Output
1
(Y/G)
Ground
Power supply
Input
Ignition
switch
ON
Selector lever in R position
12 V
2
(Y/L)
6
(Y/B)
Buzzer drive signal
Output
Ignition
switch
ON
When buzzer operation
Waveform period changes ac-
cording to the distance to an ob-
stacle.
3
(B)
Ground
GND
—
Ignition
switch
ON
—
0 V
9
(B/Y)
Ground
Sensor power supply
Output
Ignition
switch
ON
Shift position to “R” position
12 V
10
(B)
Ground
Sensor ground
—
Ignition
switch
ON
—
0 V
13
(O)
10
(B)
Center sensor signal RH
Input
Ignition
switch
ON
—
14
(L)
10
(B)
Center sensor signal LH
15
(R)
10
(B)
Corner sensor signal LH
16
(LG)
10
(B)
Corner sensor signal RH
JPNIA0232ZZ
JPNIA0233ZZ
SN-12
< ECU DIAGNOSIS >
SONAR CONTROL UNIT
Wiring Diagram - SONAR SYSTEM -
INFOID:0000000000935764
JCNWA0225GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст