Nissan Qashqai (2007-2010). Manual — part 1215
SEC-60
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
ULTRA SONIC SENSOR
ULTRA SONIC SENSOR
Description
INFOID:0000000001115998
Siren control unit sounds the siren when it received a trigger signal from ultra sonic sensor.
Component Function Check
INFOID:0000000001115999
1.
CHECK SIREN CONTROL UNIT FUNCTION
1.
Turn ignition switch OFF.
2.
Get in the vehicle and close all doors.
3.
Lock doors with Intelligent Key.
4.
Check that security indicator blinks when theft warning system is armed.
5.
With hand, intercept the signal between left and right sensors.
Does the siren sound?
YES
>> Siren control unit function is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000001116000
1.
CHECK SIREN FUNCTION
1.
Turn ignition switch ON.
2.
Perform “ACTIVE TEST” (“VEHICLE SECURITY HORN”) with CONSULT-Ill.
Does the siren sound?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK SIREN SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM and siren connectors.
3.
Check continuity between BCM harness connector and siren connector.
4.
Check continuity between siren connector and ground.
Is the inspection result normal?
YES
>> Replace siren. Refer to
SEC-153, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK SIREN CONTROL UNIT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect siren control unit and siren connector.
3.
Check continuity between siren control unit harness connector and siren connector.
4.
Check continuity between siren control unit harness connector and ground.
BCM connector
Terminal
Siren connector
Terminal
Continuity
M65
8
B68
1
Existed
16
3
Existed
Siren connector
Terminal
Ground
Continuity
B68
1
Ground
Not existed
3
Not existed
Siren control unit connector
Terminal
Siren connector
Terminal
Continuity
M94
3
B68
4
Existed
ULTRA SONIC SENSOR
SEC-61
< COMPONENT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK ULTRA SONIC SENSOR SIGNAL CIRCUIT
1.
Disconnect ultra sonic sensor connectors.
2.
Check continuity between siren control unit harness connector and ultra sonic sensor connector.
3.
Check continuity between siren control unit connector and ground.
Is the inspection result normal?
YES
>> Replace ultra sonic sensor.
NO
>> Repair or replace harness.
Siren control unit connector
Terminal
Ground
Continuity
M94
3
Ground
Not existed
Siren control unit connector
Terminal
Ultra sonic sensor connector
Terminal
Continuity
M94
1
R11
1
Existed
8
R12
1
Existed
Siren control unit connector
Terminal
Ground
Continuity
M94
1
Ground
Not existed
8
Not existed
SEC-62
< ECU DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
ECU DIAGNOSIS
BCM (BODY CONTROL MODULE)
Reference Value
INFOID:0000000001102176
VALUES ON THE DIAGNOSIS TOOL
Monitor Item
Condition
Value/Status
ACC ON SW
Ignition switch OFF
OFF
Ignition switch ACC or ON
ON
AIR COND SW
A/C switch OFF
OFF
A/C switch ON
ON
AUT LIGHT SYS
Outside of the room is dark
OFF
Outside of the room is bright
ON
AUTO LIGHT SW
Lighting switch OFF
OFF
Lighting switch AUTO
ON
BACK DOOR SW
Back door closed
OFF
Back door opened
ON
BATTERY VOLT
NOTE:
Diesel engine models
only
Ignition switch ON
Approximately the same as power
supply voltage
BUCKLE SW
Driver's seat belt unfastened
OFF
Driver's seat belt fastened
ON
CDL LOCK SW
Door lock/unlock switch does not operate
OFF
Press door lock/unlock switch to the LOCK side
ON
CDL UNLOCK SW
Door lock/unlock switch does not operate
OFF
Press door lock/unlock switch to the UNLOCK side
ON
DOOR SW-AS
Passenger door closed
OFF
Passenger door opened
ON
DOOR SW-DR
Driver door closed
OFF
Driver door opened
ON
DOOR SW-RL
Rear LH door closed
OFF
Rear LH door opened
ON
DOOR SW-RR
Rear RH door closed
OFF
Rear RH door opened
ON
ELEC PWR CUT
NOTE:
Diesel engine models
only
Engine running
Fan switch ON (when engine coolant is
cool)
NOTE:
Depending on the ambient tempera-
ture, battery voltage, etc.
OFF
The current status maintained with the
signal from ECM received.
FREEZ
• Fan switch OFF
• Fan switch ON after engine warming
UP
NOTE:
Depending on the engine coolant
temperature, ambient temperature,
battery voltage, etc.
INHBT
BCM (BODY CONTROL MODULE)
SEC-63
< ECU DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ENG COOLNT T
NOTE:
Diesel engine models
only
Engine running
Approximately the same as water
temperature gauge reading
ENGINE RPM
NOTE:
Diesel engine models
only
Engine running
Approximately the same as tachom-
eter reading
ENGINE RUN
Engine stopped
OFF
Engine running
ON
ENGINE STATUS
NOTE:
Diesel engine models
only
Engine stopped
STOP
While the engine stalls
STALL
Engine running
RUN
At engine cranking
CRA
FAN ON SIG
Fan switch OFF
OFF
Fan switch ON
ON
FR FOG SW
Front fog lamp switch OFF
OFF
Front fog lamp switch ON
ON
FR WASHER SW
Front washer switch OFF
OFF
Front washer switch ON
ON
FR WIPER LOW
Front wiper switch OFF
OFF
Front wiper switch LO
ON
FR WIPER HI
Front wiper switch OFF
OFF
Front wiper switch HI
ON
FR WIPER INT
Front wiper switch OFF
OFF
Front wiper switch INT
ON
FR WIPER STOP
Any position other than front wiper stop position
OFF
Front wiper stop position
ON
HAZARD SW
When hazard switch is not pressed
OFF
When hazard switch is pressed
ON
HEAD LAMP SW 1
Lighting switch OFF
OFF
Lighting switch 2ND
ON
HEAD LAMP SW 2
Lighting switch OFF
OFF
Lighting switch 2ND
ON
HI BEAM SW
Lighting switch OFF
OFF
Lighting switch HI
ON
HOOD SW
Close the hood
NOTE:
Vehicles without theft warning system are OFF-fixed
OFF
Open the hood
ON
H/L WASH SW
NOTE:
The item is indicated, but not monitored
OFF
IGN ON SW
Ignition switch OFF or ACC
OFF
Ignition switch ON
ON
IGN SW CAN
Ignition switch OFF or ACC
OFF
Ignition switch ON
ON
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
1 - 7
Monitor Item
Condition
Value/Status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст