Nissan Qashqai (2007-2010). Manual — part 492
FL-4
< PREPARATION >
[HR16DE, MR20DE]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000000905648
Tool name
Description
Lock ring wrench
Removing and Installing lock ring
ZZA0122D
FUEL SYSTEM
FL-5
< ON-VEHICLE MAINTENANCE >
[HR16DE, MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
ON-VEHICLE MAINTENANCE
FUEL SYSTEM
Inspection
INFOID:0000000000905649
Inspect fuel lines, fuel filler cap and fuel tank for improper attach-
ment, leaks, cracks, damage, loose connections, chafing or deterio-
ration.
If necessary, repair or replace damaged parts.
Quick Connector
INFOID:0000000000905650
CAUTION:
• After connecting fuel tube quick connectors, make sure quick connectors are secure.
• Ensure that connector and resin tube do not contact any adjacent parts.
A
: Engine
B
: Fuel line
C
: Fuel tank
JPBIA0129ZZ
FL-6
< ON-VEHICLE REPAIR >
[HR16DE, MR20DE]
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
ON-VEHICLE REPAIR
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
2WD
2WD : Exploded View
INFOID:0000000000905651
Removal and Installation
Disassembly and Assembly
1.
Lock ring
2.
Fuel level sensor unit, fuel filter and fuel pump
assembly
3.
O-ring
4.
Fuel tank
: Vehicle front
for symbols in the figure.
JPBIA0300GB
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FL-7
< ON-VEHICLE REPAIR >
[HR16DE, MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.
2WD : Removal and Installation
INFOID:0000000000905652
REMOVAL
WARNING:
Be sure to read “General Precautions” before working on the fuel system. Refer to
.
1.
Check fuel level on fuel gauge. If fuel gauge indicates more than
the level as shown in the figure (full or almost full), drain fuel
from fuel tank until fuel gauge indicates level as shown in the fig-
ure or below.
NOTE:
Because fuel will be spilled when removing fuel level sensor
unit, fuel filter and fuel pump assembly for the top of the fuel is
above the fuel level sensor units installation surface.
• As a guide, fuel level becomes the position as shown in the
figure or below when approximately 15 (3- 1/4 Imp gal) of
fuel are drained from fuel tank.
• In case fuel pump does not operate, perform the following pro-
cedure.
a.
Insert hose of less than 20 mm (0.79 in) in diameter into fuel filler tube through fuel filler opening to draw
fuel from fuel filler tube.
b.
Disconnect fuel filler hose from fuel filler tube. Refer to
c.
Insert hose into fuel tank through fuel filler hose to draw fuel from fuel tank.
2.
Release the fuel pressure from the fuel lines. Refer to
(MR20DE).
3.
Open fuel filler lid.
4.
Open fuel filler cap and release the pressure inside the fuel tank.
5.
Remove rear seat cushion. Refer to
.
6.
Remove inspection hole cover.
• Using a screwdriver, remove it by turning clips clockwise by 90 degrees.
1.
Fuel filter and fuel pump assembly
2.
Fuel level sensor unit
:Vehicle front
JPBIA0299GB
JPBIA0459ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст