Nissan Qashqai (2007-2010). Manual — part 1403
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
EXL-317
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
Description
INFOID:0000000001099388
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000001099389
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> GO TO 2.
2.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select "TAIL & CLR REQ" of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 4.
NO
>> Replace BCM. Refer to
.
4.
TAIL LAMP CIRCUIT INSPECTION
Check the tail lamp circuit. Refer to
EXL-233, "Component Function Check"
.
Is the tail lamp circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
• Parking lamp
• Tail lamp
• License plate lamp
IPDM E/R
#49
10 A
Monitor item
Condition
Monitor status
TAIL & CLR
REQ
Lighting switch
1ST
ON
OFF
OFF
EXL-318
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000001099390
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000001099391
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> GO TO 2.
2.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select "FR FOG REQ" of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the item status normal?
YES
>> GO TO 4.
NO
>> Replace BCM. Refer to
4.
FRONT FOG LAMP CIRCUIT INSPECTION
Check the front fog lamp circuit. Refer to
EXL-221, "Component Function Check"
.
Is the front fog lamp circuit normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#43
15 A
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
ON
OFF
OFF
PRECAUTIONS
EXL-319
< PRECAUTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000001078107
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRC and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRC section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
EXL-320
< ON-VEHICLE MAINTENANCE >
[HALOGEN TYPE]
HEADLAMP AIMING ADJUSTMENT
ON-VEHICLE MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000001026278
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the lug-
gage room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
• Headlamp aiming switch sets to “0”.
AIMING ADJUSTMENT SCREW
JPLIA0250ZZ
A.
Headlamp RH (UP/DOWN) adjust-
ment screw
B.
Headlamp RH (INSIDE/OUTSIDE)
adjustment screw
C.
Headlamp LH (INSIDE/OUTSIDE)
adjustment screw
D.
Headlamp LH (UP/DOWN) adjust-
ment screw
: Vehicle center
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст