Nissan Qashqai (2007-2010). Manual — part 704
BRC-14
< FUNCTION DIAGNOSIS >
[ABS]
EBD
LHD models
JSFIA0034ZZ
1.
ABS warning lamp
2.
Brake warning lamp
3.
ABS actuator and electric unit (con-
trol unit)
4.
Front wheel sensor
5.
G sensor
6.
Rear wheel sensor (2WD models)
7.
Rear wheel sensor (4WD models)
A.
Combination meter
B.
Engine room (right side)
C.
Steering knuckle
D.
Lower instrument cover RH
E.
Rear axle
EBD
BRC-15
< FUNCTION DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
RHD models
Component Description
INFOID:0000000000977416
JSFIA0048ZZ
1.
ABS warning lamp
2.
Brake warning lamp
3.
ABS actuator and electric unit (con-
trol unit)
4.
Front wheel sensor
5.
G sensor
6.
Rear wheel sensor (2WD models)
7.
Rear wheel sensor (4WD models)
A.
Combination meter
B.
Engine room (left side)
C.
Steering knuckle
D.
Lower instrument cover RH
E.
Rear axle
Component parts
Reference
ABS actuator and electric unit (control unit)
Pump
Motor
Actuator relay (Main relay)
Solenoid valve
Wheel sensor
BRC-16
< FUNCTION DIAGNOSIS >
[ABS]
EBD
ABS warning lamp
Brake warning lamp
Component parts
Reference
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-17
< FUNCTION DIAGNOSIS >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III Function (ABS)
INFOID:0000000000924967
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
SELF-DIAG RESULTS MODE
Operation Procedure
1.
Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for
approximately 1 minute.
How to Erase Self-diagnosis Results
1.
After erasing DTC memory, start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately
1 minute as the final inspection, and make sure that the ABS warning lamp and brake warning lamp turn
OFF.
CAUTION:
If memory cannot be erased, perform applicably diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning lamp
and brake warning lamp will not turn OFF even when the system is normal unless the vehicle is driving
at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or of brake fluid
level switch operation (when brake fluid is insufficient).
Display Item List
DATA MONITOR MODE
Display Item List
×
: Applicable
o
: Optional item
Diagnostic test mode
Function
Self-diagnostic results
Self-diagnostic results can be read and erased quickly.
Data monitor
Input/Output data in the ABS actuator and electric unit (control unit) can be read.
Active test
Diagnostic test mode is which CONSULT-III drives some actuators apart from the ABS actuator
and electric unit (control unit) and also shifts some parameters in a specified range.
ECU part number
ABS actuator and electric unit (control unit) part number can be read.
Function test
Performed by CONSULT-III instead of a technician to determine whether each system is “OK”
or “NG”.
CAN diagnostic support monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor item (Unit)
SELECT MONITOR ITEM
Remarks
ECU INPUT SIG-
NALS
MAIN SIGNLAS
FR LH SENSOR
[km/h (MPH)]
×
×
Wheel speed
FR RH SENSOR
[km/h (MPH)]
×
×
RR LH SENSOR
[km/h (MPH)]
×
×
RR RH SENSOR
[km/h (MPH)]
×
×
STOP LAMP SW
(On/Off)
×
×
Stop lamp switch signal status
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст