Nissan Qashqai (2007-2010). Manual — part 56
EM-172
< ON-VEHICLE REPAIR >
[MR20DE]
TIMING CHAIN
- Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
NOTE:
If hydraulic pressure inside chain tensioner drops after removal/installation, slack in guide may generate a
pounding noise during and just after the engine start. However, this does not indicate an unusualness. Noise
will stop after hydraulic pressure rises.
• Warm up engine thoroughly to make sure there is no leakage of fuel, or any oil/fluids including engine oil and
engine coolant.
• Bleed air from lines and hoses of applicable lines, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
Item
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
CAMSHAFT
EM-173
< ON-VEHICLE REPAIR >
[MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAMSHAFT
Exploded View
INFOID:0000000000893950
Removal and Installation
INFOID:0000000000893951
CAUTION:
The rotating direction in the text indicates all directions seen from the engine front.
REMOVAL
1.
Remove the following parts.
• Intake manifold: Refer to
• Rocker cover: Refer to
• Front cover and timing chain related parts: Refer to
NOTE:
1.
O-ring
2.
Camshaft position sensor (PHASE)
3.
Camshaft bracket
4.
Camshaft sprocket (EXH)
5.
Camshaft sprocket (INT)
6.
Camshaft (EXH)
7.
Camshaft (INT)
8.
Signal plate
9.
Valve lifter (EXH)
10. Valve lifter (INT)
A.
Refer to
Refer to
for symbols shown in the figure.
JPBIA0292GB
EM-174
< ON-VEHICLE REPAIR >
[MR20DE]
CAMSHAFT
Removal of balancer unit related part is not necessary.
2.
Remove camshaft position sensor (PHASE) from camshaft bracket.
CAUTION:
• Handle camshaft position sensor (PHASE) carefully and avoid impacts.
• Never disassemble camshaft position sensor (PHASE).
• Never place sensor where it is exposed to magnetism.
3.
Put the matching mark (A) on the camshaft sprocket (INT) (2)
and the camshaft bracket (1) as shown in the figure.
NOTE:
It prevents the knock pin of the camshaft (INT) from engaging
with the incorrect pin hole when installing the camshaft sprocket
(INT).
4.
Remove camshaft sprockets (INT) (1) and (EXH) (2).
• Secure hexagonal part (A) of camshaft with a wrench. Loosen
camshaft sprocket mounting bolts and remove camshaft
sprocket.
CAUTION:
• Never rotate crankshaft or camshaft while timing chain
is removed. It causes interference between valve and
piston.
• Never loosen the mounting bolts with securing anything
other than the camshaft hexagonal part or with tension-
ing the timing chain.
5.
Remove camshaft bracket with the following procedure:
a.
Loosen mounting bolts in reverse order as shown in the figure.
b.
Cut liquid gasket by prying the position (
) shown in the figure,
and then remove the camshaft bracket.
CAUTION:
• Be careful not to damage the mating surface.
• A more adhesive liquid gasket is applied compared to pre-
vious types when shipped, so it should not be forced off
the position not specified.
6.
Remove camshafts.
7.
Remove valve lifters.
• Identify installation positions, and store them without mixing them up.
: Engine front
PBIC3992J
PBIC3454J
: Engine front
PBIC3176J
: Engine front
PBIC3358J
CAMSHAFT
EM-175
< ON-VEHICLE REPAIR >
[MR20DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
8.
Remove signal plate from camshaft (INT), if necessary.
INSTALLATION
1.
Install valve lifters.
• Install them in the original positions.
2.
Install camshafts.
• Clean camshaft journal to remove any foreign material.
• Distinguish between the intake and the exhaust by looking at
the different shapes of the front and rear ends of the camshaft
or using the identification colors (A) and (B).
• Install camshafts so that camshaft dowel pins (A) on the front
side are positioned as shown in the figure.
NOTE:
Though camshaft does not stop at the positions as shown in
the figure, for the placement of cam nose, it is generally
accepted camshaft is placed for the same direction of the fig-
ure.
3.
Install camshaft bracket with the following procedure:
a.
Remove foreign material completely from camshaft bracket backside and from cylinder head installation
face.
b.
Apply liquid gasket (A) to camshaft bracket as shown in the fig-
ure.
Use Genuine Liquid Gasket or equivalent.
1
: Camshaft (EXH)
2
: Camshaft (INT)
Identification color
A
B
Camshaft (EXH)
—
White
Camshaft (INT)
White
—
1
: Camshaft (EXH)
2
: Camshaft (INT)
PBIC3188J
PBIC3189J
B
: Plug hole inner wall
: Engine front
: Engine outside
PBIC3964E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст