Nissan Qashqai (2007-2010). Manual — part 819
B1153 CURTAIN MODULE LH
SRC-163
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
With CONSULT-III
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Are connections of harness connectors and terminals correct?
YES
>> GO TO 2.
NO
>> Repair or replace harness connector.
2.
CHECK WIRING HARNESS
Is the outside of wiring harness normal, without any damage?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK SIDE CURTAIN AIR BAG MODULE
Is “AIR BAG” displayed on CONSULT-III?
YES
>> Replace side curtain air bag module.
NO
>> Replace diagnosis sensor unit (ACU).
SRC-164
< COMPONENT DIAGNOSIS >
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000001070023
DTC B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester “CONSULT-III”.
OPERATION
It detects a shock that exceeds specified level and watches such systems as the driver and passenger air bag,
side air bag, curtain air bag, pre-tensioner seat belts operate properly.
STRUCTURE
It contains the “G” sensors of both for frontal collision and for side collision and spare battery function in case
of main battery damage in collision.
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
DTC Logic
INFOID:0000000001070024
DTC DETECTION LOGIC
With CONSULT-III
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
Without CONSULT-III
Warning Lamp Flash Code Chart
DTC CONFIRMATION PROCEDURE (With CONSULT-III)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
CONSULT-III
Check the “SELF-DIAG” RESULT with CONSULT-III.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1170
B1171
B1172
B1173
B1174
B1175
DIAGNOSIS SENSOR
UNIT
Diagnosis sensor unit is out of order.
1.
Replace diagnosis sensor unit
(ACU).
JMHIA0034GB
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
SRC-165
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
>> GO TO 3.
3.
DTC CODE
If DTC is detected. Refer to
>> END
DTC CONFIRMATION PROCEDURE (Without CONSULT-III)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
USER MODE-DIAG MODE
After air bag warning lamp illuminates for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3.
3.
USER MODE-DIAG MODE
Wait more than 3 seconds.
>> GO TO 4.
4.
USER MODE-DIAG MODE
Repeat step 1 to 3 twice. (Perform three times in all.)
>> GO TO 5.
5.
DIAG MODE
Turn ignition switch ON. (SRS is now in diagnosis mode.)
>> GO TO 6.
6.
DIAG MODE (AIR BAG WARNING LAMP)
Malfunctioning portion is indicated according to blinking times of air bag warning lamp. Refer to
>> END
Diagnosis Procedure (Component diagnosis)
INFOID:0000000001070025
SRC-166
< COMPONENT DIAGNOSIS >
B1170, B1171, B1172, B1173, B1174, B1175 DIAGNOSIS SENSOR UNIT
With CONSULT-III
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Are connections of harness connectors and terminals correct?
YES
>> GO TO 2.
NO
>> Repair or replace harness connectors.
2.
CHECK WIRING HARNESS
Is the outside of wiring harness normal, without any damage?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK DIAGNOSIS SENSOR UNIT
Is “DIAGNOSIS SENSOR UNIT” displayed on CONSULT-III?
YES
>> Replace diagnosis sensor unit (ACU).
>> INSPECTION END.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст