Nissan Qashqai (2007-2010). Manual — part 895
HA-150
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (HR/MR)]
LOW-PRESSURE PIPE 1 AND HIGH-PRESSURE PIPE 2
9.
Disconnect Heater and cooling unit harness connectors from steering member main harness.
10. Remove steering member.
11. Remove heater and cooling assembly. Refer to
VTL-32, "Removal and Installation"
.
12. Remove mounting screws, and then remove evaporator cover
(1).
13. Using a thin cutter, cut the evaporator insulator (B), and then
remove fixing bolt (A) and low-pressure pipe 1 and high-pres-
sure pipe 2 assembly.
CAUTION:
Cap or wrap the joint of expansion valve, high-pressure
pipe 2 and low-pressure pipe 1 with suitable material such
as vinyl tape to avoid the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of high-pressure pipe 1, 2 and low-pressure pipe 1, 2 with new ones, and then apply
compressor oil to it when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
E1KIA0048ZZ
E1KIA0049ZZ
CONDENSER
HA-151
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (HR/MR)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER
Exploded View
INFOID:0000000001098174
Removal and Installation
INFOID:0000000001098175
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove engine cover ornament. Refer to
EM-27, "Removal and Installation"
.
3.
Remove front grille. Refer to
EXT-17, "Removal and Installation"
4.
Remove radiator hose, and drain coolant. Refer to
(MR).
5.
Remove upper radiator fixing bracket. Refer to
(MR).
6.
Remove radiator air-guide duct (RH). Refer to
(HR),
(MR).
7.
Remove high-pressure pipe 1 fixing bolt (A) and high pressure
pipe (1) from liquid tank. Refer to
.
8.
Remove high-pressure flexible pipe 1 from condenser. Refer to
HA-145, "Removal and Installation"
CAUTION:
Cap or wrap the joint of low and high-pressure pipe 1 and
condenser with suitable material such as vinyl tape to avoid
the entry of air.
9.
Remove harness connector from refrigerant pressure sensor.
10. Remove liquid tank pipes and liquid tank from condenser and
radiator. Refer to
HA-153, "Removal and Installation"
.
CAUTION:
Cap or wrap the joint of liquid tank pipes and condenser with suitable material such as vinyl tape
to avoid the entry of air.
11. Remove radiator fixing brackets. Refer to
12. Release radiator maintaining pawls, then pull-up the condenser assembly to release it from radiator. Refer
CO-13, "Removal and Installation"
CO-35, "Removal and Installation"
(MR).
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condenser
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing bolt
E1KIA0050GB
JMIIA0002ZZ
HA-152
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (HR/MR)]
CONDENSER
13. Maintain radiator pushing back.
14. Pull upward to remove condenser.
CAUTION:
Take care do not damaged condenser or radiator.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of high-pressure flexible hose and high-pressure pipe 1 with new ones, and then
apply compressor oil to it when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
LIQUID TANK
HA-153
< ON-VEHICLE REPAIR >
[MANUAL AIR CONDITIONER (HR/MR)]
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
LIQUID TANK
Exploded View
INFOID:0000000001098178
Removal and Installation
INFOID:0000000001098179
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove engine cover ornament. Refer to
3.
Clean liquid tank and its surrounding area, and remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
4.
Disconnect refrigerant sensor harness connector. Refer to
HA-154, "Removal and Installation"
.
5.
Remove liquid tank bracket support mounting screws (B).
6.
Remove high pressure pipe 1 (1) mounting bolt (A) from liquid
tank. Refer to
HA-147, "Removal and Installation"
.
7.
Remove liquid tank high pressure pipe mounting bolt (A) from
condenser.
8.
Remove liquid tank pipe bracket fixing screw.
CAUTION:
Cap or wrap the joint of high pressure pipe, liquid tank
pipes and condenser with suitable material such as vinyl
tape to avoid the entry of air.
9.
Remove liquid tank assembly.
INSTALLATION
Install liquid tank, and then install liquid tank bracket on condenser.
CAUTION:
• Make sure liquid tank bracket is securely installed at protrusion of condenser. (Make sure liquid tank
bracket does not move to a position below center of liquid tank.)
• Replace O-rings of A/C piping with new ones, and then apply compressor oil to it when installing it.
• When recharging refrigerant, check for leaks.
1.
Refrigerant pressure sensor
2.
O-ring
3.
Liquid tank bracket
4.
Liquid tank
5.
Condenser
6.
Liquid tank fixing screw
7.
Liquid tank pipe fixing bolt
E1KIA0050GB
E1KIA0068ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст