Nissan Qashqai (2007-2010). Manual — part 1701
LAN
EPS BRANCH LINE CIRCUIT
LAN-829
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 55)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
EPS BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001057134
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the EPS control unit for damage, bend and loose connection (unit
side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of EPS control unit.
2.
Check the resistance between the EPS control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the EPS control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the EPS control unit. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the EPS control unit. Refer to
YES (Past error)>>Error was detected in the EPS control unit branch line.
NO
>> Repair the power supply and the ground circuit.
EPS control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M37
8
6
Approx. 54 – 66
LAN-830
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 55)]
I-KEY BRANCH LINE CIRCUIT
I-KEY BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001057135
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the Intelligent Key unit for damage, bend and loose connection
(unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of Intelligent Key unit.
2.
Check the resistance between the Intelligent Key unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the Intelligent Key unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the Intelligent Key unit. Refer to
KEY UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES (Present error)>>Replace the Intelligent Key unit. Refer to
SEC-11, "Component Parts Location"
YES (Past error)>>Error was detected in the Intelligent Key unit branch line.
NO
>> Repair the power supply and the ground circuit.
Intelligent Key unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M40
2
3
Approx. 54 – 66
LAN
STRG BRANCH LINE CIRCUIT
LAN-831
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 55)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
STRG BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001057136
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection
(unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of steering angle sensor.
2.
Check the resistance between the steering angle sensor harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the steering angle sensor branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the steering angle sensor. Refer to
gram - BRAKE CONTROL SYSTEM -"
.
Is the inspection result normal?
YES (Present error)>>Replace the steering angle sensor. Refer to
.
YES (Past error)>>Error was detected in the steering angle sensor branch line.
NO
>> Repair the power supply and the ground circuit.
Steering angle sensor harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M30
4
8
Approx. 54 – 66
LAN-832
< COMPONENT DIAGNOSIS >
[CAN SYSTEM (TYPE 55)]
IPDM-E BRANCH LINE CIRCUIT
IPDM-E BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000001057137
INSPECTION PROCEDURE
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
IPDM E/R connector
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of IPDM E/R.
2.
Check the resistance between the IPDM E/R harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the IPDM E/R branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the IPDM E/R. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the IPDM E/R. Refer to
.
YES (Past error)>>Error was detected in the IPDM E/R branch line.
NO
>> Repair the power supply and the ground circuit.
IPDM E/R harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E12
28
29
Approx. 108 – 132
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст