Nissan Qashqai (2007-2010). Manual — part 17
EM-16
< ON-VEHICLE MAINTENANCE >
[HR16DE]
DRIVE BELTS
CAUTION:
• When the lock nut is loosened excessively, the idler pulley tilts and the correct tension adjust-
ment cannot be performed. Never loosen it excessively (more than 45 degrees).
• Put a matching mark on the lock nut, and check turning angle with a protractor. Never visually
check the tightening angle.
3.
Adjust the belt tension by turning the adjusting bolt.
CAUTION:
• When checking immediately after installation, first adjust it to the specified value. Then, after
turning crankshaft two turns or more, re-adjust to the specified value to avoid variation in deflec-
tion between pulleys.
• When the tension adjustment is performed, the lock nut should be in the condition at step“2”. If
the tension adjustment is performed when the lock nut is loosened more than the standard, the
idler pulley tilts and the correct tension adjustment cannot be performed.
4.
Tighten the lock nut.
Removal and Installation
INFOID:0000000000894049
REMOVAL
1.
Remove front fender protector (RH). Refer to
2.
Loosen the idler pulley lock nut (A), and then adjust the belt ten-
sion by turning the adjusting bolt (B).
3.
Remove drive belt.
INSTALLATION
1.
Pull the idler pulley in the loosening direction, and then tempo-
rarily tighten the lock nut (A) to the following torque.
NOTE:
Do not move the lock nut from the tightened position. Go to step “2”.
2.
Install the drive belt to each pulley.
CAUTION:
• Make sure that there is no oil, grease, or coolant, etc. in pulley grooves.
• Make sure that the belt is securely inside the groove on each pulley.
3.
Adjust drive belt tension by turning the adjusting bolt. Refer to
.
: 34.8 N·m (3.5 kg-m, 26 ft-lb)
1
: Alternator
2
: Water pump
3
: Crankshaft pulley
4
: A/C compressor (with A/C models)
: Idler pulley (without A/C models)
5
: Idler pulley
6
: Drive belt
PBIC3643E
1
: Alternator
2
: Water pump
3
: Crankshaft pulley
4
: A/C compressor (with A/C models)
: Idler pulley (without A/C models)
5
: Idler pulley
6
: Drive belt
B
: Adjusting bolt
: 4.4 N·m (0.45 kg-m, 39 in-lb)
PBIC3643E
DRIVE BELTS
EM-17
< ON-VEHICLE MAINTENANCE >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAUTION:
• Perform the belt tension adjustment with the lock nut temporarily tightened at the step “1” so as
not to tilt the idler pulley.
• When checking immediately after installation, first adjust it to the specified value. Then, after
turning crankshaft two turns or more, re-adjust to the specified value to avoid variation in deflec-
tion between pulleys.
4.
Tighten the lock nut.
5.
Make sure that belt tension of each belt within the standard.
: 34.8 N·m (3.5 kg-m, 26 ft-lb)
EM-18
< ON-VEHICLE MAINTENANCE >
[HR16DE]
AIR CLEANER FILTER
AIR CLEANER FILTER
Removal and Installation
INFOID:0000000000893830
REMOVAL
1.
Unhook clips (A) and remove holder (2) from air cleaner case
(1).
2.
Remove air cleaner filter (1) from air cleaner case (2).
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the air cleaner filter by aligning the seal with the notch of air cleaner case.
JPBIA0464ZZ
JPBIA0465ZZ
SPARK PLUG
EM-19
< ON-VEHICLE MAINTENANCE >
[HR16DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
SPARK PLUG
Exploded View
INFOID:0000000000893831
Removal and Installation
INFOID:0000000000893832
REMOVAL
1.
Remove intake manifold. Refer to
EM-29, "Removal and Installation"
2.
Remove ignition coil. Refer to
EM-43, "Removal and Installation"
.
1.
Ignition coil
2.
Spark plug
3.
PCV hose
4.
Oil filler cap
5.
Rocker cover
6.
Gasket
7.
Bracket
8.
Grommet
9.
PCV valve
10.
PCV hose
A.
To air duct
Refer to
for symbols in the figure.
PBIC4257E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст