Nissan Qashqai (2007-2010). Manual — part 743

BRC-170

< PRECAUTION >

[ESP/TCS/ABS]

PRECAUTIONS

• If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness

pinches, open circuits, and improper wiring.

• ESP system may not operate normally or a ESP OFF indicator lamp or SLIP indicator lamp may light.
- When replacing the following parts with parts other than genuine parts or making modifications: Suspension-

related parts (shock absorber, spring, bushing, etc.), tires, wheels (other than specified sizes), brake-related
parts (pad, rotor, caliper, etc.), engine-related parts (muffler, ECM, etc.) and body reinforcement-related parts
(roll bar, tower bar, etc.).

- When driving with worn or deteriorated suspension, tires and brake-related parts.

PREPARATION

BRC-171

< PREPARATION >

[ESP/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000000936578

Tool number
Tool name

Description

GG94310000
Flare nut torque wrench
a: 10 mm (0.39 in)/ 12 mm (0.47 in)

Installing each brake piping

S-NT406

BRC-172

< ON-VEHICLE REPAIR >

[ESP/TCS/ABS]

WHEEL SENSOR

ON-VEHICLE REPAIR

WHEEL SENSOR

FRONT WHEEL SENSOR

FRONT WHEEL SENSOR : Exploded View

INFOID:0000000001115340

NOTE:
The above figure (front side) shows left side. Right side is the mirror image.

FRONT WHEEL SENSOR : Removal and Installation

INFOID:0000000001115341

REMOVAL

Pay attention to the following when removing sensor.

CAUTION:

• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling

on sensor harness.

• Take care to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-

ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.

• When you see the harness of the wheel sensor from the front side of the vehicle ensure that the

white lines (A) are not twisted.

INSTALLATION

Pay attention to the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to

BRC-67, "FRONT WHEEL SENSOR : Exploded View"

.

• When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of the

wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign mate-
rial and clean the mount.

• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above

in the figure. When installed, harness must not be twisted.

REAR WHEEL SENSOR

REAR WHEEL SENSOR : Exploded View

INFOID:0000000001115342

1.

Front LH wheel sensor

A.

White line (slant line)

Refer to GI section

GI-4, "Components"

for symbols in the figure.

JSFIA0039GB

WHEEL SENSOR

BRC-173

< ON-VEHICLE REPAIR >

[ESP/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

NOTE:
The above figure (front side) shows left side. Right side is the mirror image.

REAR WHEEL SENSOR : Removal and Installation

INFOID:0000000001115343

REMOVAL

Pay attention to the following when removing sensor.

CAUTION:

• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling

on sensor harness.

• Take care to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-

ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.

INSTALLATION

Pay attention to the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to

BRC-67, "REAR WHEEL SENSOR : Exploded View"

.

• When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of the

wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign mate-
rial and clean the mount.

• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above

in the figure. When installed, harness must not be twisted.

1.

Rear LH wheel sensor

A.

2WD models

B.

4WD models

Refer to GI section

GI-4, "Components"

for symbols in the figure.

JSFIA0040GB