Nissan Qashqai (2007-2010). Manual — part 504
STR-2
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
K9K MODELS
K9K MODELS : Work Flow
INFOID:0000000001116764
OVERALL SEQUENCE
JSBIA0008GB
DIAGNOSIS AND REPAIR WORKFLOW
STR-3
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
DETAILED FLOW
NOTE:
If any malfunction is found, immediately disconnect the battery cable from the negative terminal.
1.
CHECK ENGINE START
Crank the engine and check that the engine starts.
Does the engine start?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK THAT THE STARTER MOTOR STOPS
Check that the starter motor stops after starting the engine.
Does the starter motor stop?
YES
>> INSPECTION END
NO
>> Replace starter motor.
3.
CHECK THE ENGINE SPEED WITH CRANKING
Check that the engine runs at cranking.
Does engine turn by cranking?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CHECK THE ENGINE SPEED WITH CRANKING
Check that the engine speed is not low at cranking.
Does engine turn normally?
YES
>> Check ignition/fuel system.
NO
>> Check charge condition, corrosion and connection condition of the battery. Refer to
5.
CHECK STARTER MOTOR ACTIVATION
Check that the starter motor runs at cranking.
Does starter motor turn?
YES
>> GO TO 6.
NO
>> GO TO 7.
6.
ENGINE ROTATION STATUS
Check that the engine can be rotated by hand.
Does engine turn freely by hand?
YES
>> Replace starter motor.
NO
>> Perform further diagnosis of engine mechanical or powertrain mechanism. Refer to EM, TM or CL
sections.
7.
CHECK POWER SUPPLY CIRCUIT
Check the following conditions.
• Fuse and fusible link
• Charge condition, corrosion and connection condition of the battery. Refer to
.
Are these inspection results normal?
YES
>> GO TO 8.
NO
>> Repair as needed.
8.
CHECK STARTING SYSTEM WIRING
Check the following.
• “B” terminal circuit. Refer to
• “S” terminal circuit. Refer to
Are these inspection results normal?
YES
>> GO TO 9.
NO
>> Repair as needed.
STR-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
9.
CHECK MAGNETIC SWITCH OPERATION SOUND
Check that a magnetic switch operation sound can be heard when the ignition switch is set at the starting posi-
tion.
Does magnetic switch operation sound occur?
YES
>> GO TO 10.
NO
>> Replace starter motor.
10.
PINION AND RING GEAR ENGAGEMENT CHECK
Check condition of pinion and ring gear mesh.
Is the inspection result normal?
YES
>> Replace starter motor.
NO
>> GO TO 11.
11.
CHECK STARTER MOTOR UNIT
Check the following.
• Check pinion moving mechanism.
• Check ring gear.
Are these inspection results normal?
YES
>> INSPECTION END
NO
>> Repair or replace, if necessary.
HR16DE/MR20DE MODELS
HR16DE/MR20DE MODELS : Work Flow
INFOID:0000000000955263
DIAGNOSIS AND REPAIR WORKFLOW
STR-5
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
OVERALL SEQUENCE
DETAILED FLOW
NOTE:
If any malfunction is found, immediately disconnect the battery cable from the negative terminal.
1.
CHECK ENGINE START
Crank the engine and check that the engine starts.
Does the engine start?
JPBIA0502GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст