Nissan Qashqai (2007-2010). Manual — part 621
4WD CONTROL UNIT
DLN-57
< ON-VEHICLE REPAIR >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
RHD : Removal and Installation
INFOID:0000000000972130
REMOVAL
1.
Remove the instrument assist lower panel. Refer to
2.
Disconnect 4WD control unit harness connector.
3.
Remove 4WD control unit (1) mounting screws.
4.
Remove 4WD control unit.
INSTALLATION
Install is the reverse order of removal.
1.
4WD control unit
: Vehicle front
JSDIA0239ZZ
JSDIA0240ZZ
DLN-58
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
TRANSFER ASSEMBLY
REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
M/T
M/T : Exploded View
INFOID:0000000001055585
M/T : Removal and Installation
INFOID:0000000001055586
REMOVAL
1.
Remove the exhaust front tube. Refer to
2.
Remove the exhaust manifold. Refer to
.
3.
Separate the rear propeller shaft. Refer to
4.
Remove right side drive shaft and support bearing bracket. Refer to
5.
Remove the mounting bolts (
) of transaxle assembly and
transfer assembly.
CAUTION:
Never remove the mounting bolts (
) of adapter case.
6.
Remove transfer assembly from the vehicle.
CAUTION:
• Never damage ring gear shaft.
• Never damage air breather hose.
7.
Remove O-ring (outer) from the transfer assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Apply multi-purpose grease lightly and evenly onto an O-ring (outer), and install it to the transfer assembly.
CAUTION:
Never reuse O-ring (outer).
1.
Transfer assembly
2.
O-ring (outer)
: Vehicle front
Refer to
for symbols in the figure.
JSDIA0210GB
SDIA3225J
TRANSFER ASSEMBLY
DLN-59
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Install mounting bolts according to the standard below when install-
ing transfer assembly to the transaxle assembly.
• Check oil level and check for oil leakage after installation. Refer to
.
CVT
CVT : Exploded View
INFOID:0000000000972135
CVT : Removal and Installation
INFOID:0000000000972136
REMOVAL
1.
Remove the exhaust front tube. Refer to
2.
Remove the exhaust manifold. Refer to
.
3.
Separate the rear propeller shaft. Refer to
4.
Remove right side drive shaft and support bearing bracket. Refer to
5.
Remove the mounting bolts (
) of transaxle assembly and
transfer assembly.
CAUTION:
Never remove the mounting bolts (
) of adapter case.
6.
Remove transfer assembly from the vehicle.
CAUTION:
• Never damage ring gear shaft.
• Never damage air breather hose.
Bolt symbol
A
B
Installation direction
Transfer
⇒
Transaxle
Transaxle
⇒
Transfer
SDIA3070J
1.
Transfer assembly
: Vehicle front
Refer to
JSDIA0209GB
SDIA3225J
DLN-60
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
TRANSFER ASSEMBLY
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install mounting bolts according to the standard below when install-
ing transfer assembly to the transaxle assembly.
CAUTION:
Replace side oil seal (transfer joint) of transaxle assembly
when installing transfer assembly to the transaxle assembly.
Never damage oil seal. Refer to
• Check oil level and check for oil leakage after installation. Refer to
Bolt symbol
A
B
Installation direction
Transfer
⇒
Transaxle
Transaxle
⇒
Transfer
SDIA3070J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст