Nissan Qashqai (2007-2010). Manual — part 748
STEERING COLUMN
ST-11
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
a.
Remove fixing bolt (1).
b.
Remove pressed cam nut holder (2) from intermediate shaft
yoke.
c.
Remove cam nut (3).
11. Remove steering column assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Never impact on the axis when removing steering column assembly.
• Place a matching mark on both intermediate shaft and steering column assembly before removing
intermediate shaft.
• Never repeat static steering. (Motor and EPS control unit is heated.)
• Be careful when removing steering column assembly from the vehicle because it is heavy.
• Keep steering column assembly away from magnetic sources.
• Never disassemble steering column assembly. It is not separable.
Be careful of the following points when installing the steering column assembly.
CAUTION:
Never reuse cam nut and fixing bolt.
1.
Check that all parts of the cam nut holder are removed.
2.
Fit yoke to pinion shaft, ensuring no clearance between yoke and pinion shaft.
3.
Insert cam nut fully.
4.
Whilst holding cam nut in position by hand, insert bolt and tighten to specified torque. Take care to hold
cam nut in correct axial position during this process.
5.
After intermediate shaft fitted, make sure there is no gap (A)
between the yoke (1), pinion shaft (2) and cam nut (3).
CAUTION:
Adjust neutral position of steering angle sensor. Refer to
78, "ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
.
Inspection
INFOID:0000000000953499
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are.
• Measure steering column assembly rotating torque using a preload gauge (SST: ST3127S000). Replace
steering column assembly if outside the standard.
JSGIA0132ZZ
JSGIA0165ZZ
Standard
Rotating torque
: Refer to
ST-12
< ON-VEHICLE REPAIR >
STEERING COLUMN
• Measure the length “L” as shown, if vehicle has been involved in a
minor collision. Replace steering column assembly (with motor,
reduction gear, sensor) if outside the standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if there are.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt and telescopic mechanism operating range “L
1
”, “L
2
” as
shown in the figure.
Standard
Steering column length “L”
: Refer to
SGIA1345J
Standard
Tilt operating range “L
1
”
: Refer to
Telescopic operating
range “L
2
”
: Refer to
JSGIA0135ZZ
STEERING GEAR AND LINKAGE
ST-13
< ON-VEHICLE REPAIR >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
STEERING GEAR AND LINKAGE
Exploded View
INFOID:0000000000953510
REMOVAL AND INSTALLATION
LHD models
RHD models
DISASSEMBLY AND ASSEMBLY
JSGIA0138GB
1.
Fire wall seal
2.
Steering gear assembly
3.
Front suspension member
: Vehicle front
Refer to
JSGIA0136GB
1.
Fire wall seal
2.
Steering gear assembly
3.
Heat insulator
4.
Front suspension member
: Vehicle front
Refer to
ST-14
< ON-VEHICLE REPAIR >
STEERING GEAR AND LINKAGE
LHD models
RHD models
JSGIA0139GB
1.
Outer socket
2.
Outer socket lock nut
3.
Inner socket
4.
Boot clamp (small diamater)
5.
Boot
6.
Boot clamp (large diameter)
7.
Gear housing assembly
: Apply Molywhite LSG or equivalent.
Refer to
for symbols not described on the above.
JSGIA0137GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст