Nissan Qashqai (2007-2010). Manual — part 282
INSPECTION AND ADJUSTMENT
EC-647
< BASIC INSPECTION >
[MR20DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
>> GO TO 4
4.
CHECK IDLE SPEED AND IGNITION TIMING
Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifi-
cations. For specification, refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
DETECT MALFUNCTIONING PART
Check the following
• Check that throttle valve is fully closed.
• Check PCV valve operation.
• Check that downstream of throttle valve is free from air leakage.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace malfunctioning part.
6.
DETECT MALFUNCTIONING PART
Engine component parts and their installation condition are questionable. Check and eliminate the cause of
the incident.
It is useful to perform “TROUBLE DIAGNOSIS - SPECIFICATION VALUE”. Refer to
If any of the following conditions occur after the engine has started, eliminate the cause of the incident and
perform Idle Air Volume Learning all over again:
• Engine stalls.
• Erroneous idle.
>> INSPECTION END
MIXTURE RATIO SELF-LEARNING VALUE CLEAR
MIXTURE RATIO SELF-LEARNING VALUE CLEAR : Description
INFOID:0000000001092493
This describes how to erase the mixture ratio self-learning value. For the actual procedure, follow the instruc-
tions in “Diagnosis Procedure”.
MIXTURE RATIO SELF-LEARNING VALUE CLEAR : Special Repair Requirement
INFOID:0000000001092494
1.
START
With CONSULT-III
1.
Start engine and warm it up to normal operating temperature.
2.
Select “SELF-LEARNING CONT” in “WORK SUPPORT” mode with CONSULT-III.
3.
Clear mixture ratio self-learning value by touching “CLEAR”.
With GST
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch OFF.
3.
Disconnect mass air flow sensor harness connector.
4.
Restart engine and let it idle for at least 5 seconds.
5.
Stop engine and reconnect mass air flow sensor harness connector.
6.
Select Service $03 with GST. Make sure DTC P0102 is detected.
7.
Select Service $04 with GST to erase the DTC P0102.
>> END
EC-648
< FUNCTION DIAGNOSIS >
[MR20DE (WITH EURO-OBD)]
ENGINE CONTROL SYSTEM
FUNCTION DIAGNOSIS
ENGINE CONTROL SYSTEM
System Diagram
INFOID:0000000000936604
System Description
INFOID:0000000000936605
JMBIA0453GB
ENGINE CONTROL SYSTEM
EC-649
< FUNCTION DIAGNOSIS >
[MR20DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ECM performs various controls such as fuel injection control and ignition timing control.
Component Parts Location
INFOID:0000000001093462
1.
Ignition coil (with power transistor)
and spark plug
2.
PCV valve
3.
Refrigerant pressure sensor
4.
Fuel injector
5.
Knock sensor
6.
Cooling fan motor
7.
Camshaft position sensor (PHASE)
8.
Engine coolant temperature sensor
9.
IPDM E/R
10. ECM
11.
Mass air flow sensor (with intake
temperature sensor)
12. Electric throttle control actuator
(with built in throttle position sensor
and throttle control motor)
13. EVAP canister purge volume control
solenoid valve
1.
ECM
2.
IPDM E/R
3.
Fuel pump fuse (15A)
JMBIA0338ZZ
JMBIA0340ZZ
EC-650
< FUNCTION DIAGNOSIS >
[MR20DE (WITH EURO-OBD)]
ENGINE CONTROL SYSTEM
1.
Electric throttle control actuator
(with built-in position sensor, throttle
control motor)
2.
Throttle valve
1.
EVAP canister purge volume control
solenoid valve
2.
Mass air flow sensor
(with intake air temperature sensor)
1.
Camshaft position sensor
2.
Engine coolant temperature sensor
JMBIA0341ZZ
JMBIA0342ZZ
JMBIA0343ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст