Nissan Qashqai (2007-2010). Manual — part 654
FAX-38
< ON-VEHICLE REPAIR >
[2WD]
FRONT DRIVE SHAFT
13. Pinch projection on the band with suitable pliers to tighten band.
14. Insert tip of band below end of the pawl.
15. Secure housing and shaft, and then make sure that they are in
the correct position when rotating boot. Install them with new
boot band when the mounting positions become incorrect.
16. Install circular clip to shaft (left side).
CAUTION:
Never reuse circular clip.
17. Install dust shield (left side).
CAUTION:
Never reuse dust shield.
Support Bearing
1.
Install dust shield on housing.
CAUTION:
Never reuse dust shield.
2.
Press support bearing onto housing.
3.
Install snap ring.
CAUTION:
Never reuse snap ring.
4.
Install dust shields.
CAUTION:
Never reuse dust shields.
Dynamic Damper
Secure dynamic damper with bands in the following specified posi-
tion when removing.
CAUTION:
Never reuse bands.
Wheel Side
For further details, refer to the installation procedure of “
” for the drive shaft boot.
K9K MODELS : Inspection
INFOID:0000000001070386
SDIA3558E
YAX007
YAX008
Standard
.
FAC0156D
FRONT DRIVE SHAFT
FAX-39
< ON-VEHICLE REPAIR >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-
cant looseness.
• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there
is a non-standard condition.
INSPECTION AFTER DISASSEMBLY
Shaft
Check shaft for runout, cracks, or other damage. Replace if there are.
Dynamic Damper
Check damper for cracks or wear. Replace if necessary.
Joint Sub-Assembly (Wheel Side)
Check the following:
• Joint sub-assembly for rough rotation and excessive axial looseness
• The inside of the joint sub-assembly for entry of foreign material
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly
Replace joint sub-assembly if there are any non-standard conditions of components.
Housing and Spider assembly (Transaxle Side)
Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.
Support Bearing (Right Side)
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear. Replace support bearing if
there are any non-standard conditions.
Support Bearing Bracket (Right Side)
Check for bending, cracks, or damage. Replace support bearing bracket if there are any non-standard condi-
tions.
SDIA1190J
FAX-40
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000000970490
Drive Shaft
INFOID:0000000000970491
HR16DE
MR20DE
M/T models
Axial end play
0.05 mm (0.002 in) or less
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
100 – 120 g (3.53 – 4.23 oz)
155 – 175 g (5.47 – 6.17 oz)
Right side
Boots installed length (L)
Left side
131 mm (5.16 in)
172.4 mm (6.79 in)
Right side
Dynamic damper
A
B
Dimension
Left side
287 – 291 mm (11.30 – 11.46 in)
70 mm (2.76 in)
Right side
JPDIF0031ZZ
FAC0156D
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
115 – 135 g (4.06 – 4.76 oz)
95 – 105 g (3.35 – 3.70 oz)
Right side
113 – 123 g (3.99 – 4.34 oz)
SERVICE DATA AND SPECIFICATIONS (SDS)
FAX-41
< SERVICE DATA AND SPECIFICATIONS (SDS)
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
CVT models
Boots installed length (L)
Left side
133.5 mm (5.26 in)
185.6 mm (7.31 in)
Right side
177.6 mm (6.99 in)
Dynamic damper
A
B
Dimension
Left side
269 – 273 mm (10.59 – 10.75 in)
70 mm (2.76 in)
Right side
JPDIF0031ZZ
FAC0156D
Joint
Wheel side
Transaxle assembly side
Grease quantity
Left side
115 – 135 g (4.06 – 4.76 oz)
200 – 220 g (7.05 – 7.76 oz)
Right side
Boots installed length (L)
Left side
133.5 mm (5.26 in)
185.6 mm (7.31 in)
Right side
177.6 mm (6.99 in)
Dynamic damper
A
B
JPDIF0031ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст