Nissan Qashqai (2007-2010). Manual — part 210
SERVICE DATA AND SPECIFICATIONS (SDS)
EC-359
< SERVICE DATA AND SPECIFICATIONS (SDS)
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Idle Speed
INFOID:0000000001059496
*: Under the following conditions
• A/C switch: OFF
• Electric load: OFF (Lights, heater fan & rear window defogger)
• Steering wheel: Kept in straight-ahead position
Ignition Timing
INFOID:0000000001059497
*: Under the following conditions
• A/C switch: OFF
• Electric load: OFF (Lights, heater fan & rear window defogger)
• Steering wheel: Kept in straight-ahead position
Calculated Load Value
INFOID:0000000001059498
Mass Air Flow Sensor
INFOID:0000000001059499
*: Engine is warmed up to normal operating temperature and running under no load.
Transmission
Condition
Specification
M/T
No load* (in Neutral position)
650
±
50 rpm
Transmission
Condition
Specification
M/T
No load* (in Neutral position)
15
±
5
°
BTDC
Condition
Specification (Using CONSULT-III or GST)
At idle
10 – 35 %
At 2,500 rpm
10 – 35 %
Supply voltage
Battery voltage (11 – 14 V)
Output voltage at idle
1.0 – 1.3V*
Mass air flow (Using CONSULT-III or GST)
1.0 – 4.0 g·m/sec at idle*
2.0 – 10.0 g·m/sec at 2,500 rpm*
EC-360
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000001096723
OVERALL SEQUENCE
DETAILED FLOW
JMBIA0078GB
DIAGNOSIS AND REPAIR WORKFLOW
EC-361
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred) using the “Diagnostic Work Sheet”. (Refer to
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is displayed.
-
Record DTC and freeze frame data. (Print them out with CONSULT-III.)
-
Erase DTC. (Refer to
EC-426, "Diagnosis Description"
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
(Symptom Table is useful. Refer to
3.
Check related service bulletins for information.
Is any symptom described and is any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer (except MI ON).
Also study the normal operation and fail safe related to the symptom. Refer to
and
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail safe related to the symptom. Refer to
and
Diagnosis Work Sheet is useful to verify the incident.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the displayed DTC, and then make sure that DTC is
detected again.
If two or more DTCs are detected, refer to
EC-620, "DTC Inspection Priority Chart"
and determine trouble
diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 10.
NO
>> Check according to
6.
PERFORM BASIC INSPECTION
Perform
EC-365, "BASIC INSPECTION : Special Repair Requirement"
.
Do you have CONSULT-III?
EC-362
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
DIAGNOSIS AND REPAIR WORKFLOW
YES
>> GO TO 7.
NO
>> GO TO 9.
7.
PERFORM SPEC IN DATA MONITOR MODE
With CONSULT-III
Make sure that “MAS A/F SE-B1”, “B/FUEL SCHDL” and “A/F ALPHA-B1” are within the SP value using CON-
SULT-III in “SPEC” of “DATA MONITOR” mode. Refer to
EC-438, "Component Function Check"
.
Is the measurement value within the SP value?
YES
>> GO TO 9.
NO
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY TROUBLE DIAGNOSIS - SPECIFICATION VALUE
Detect malfunctioning part according to
.
Is malfunctioning part detected?
YES
>> GO TO 11.
NO
>> GO TO 9.
9.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to
based on the confirmed symptom in
step 4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 10.
10.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Inspect according to Diagnosis Procedure of the system.
NOTE:
The Diagnosis Procedure in EC section described based on open circuit inspection. A short circuit inspection
is also required for the circuit check in the Diagnosis Procedure. For details, refer to Circuit Inspection in
Is malfunctioning part detected?
YES
>> GO TO 11.
NO
>> Monitor input data from related sensors or check the voltage of related ECM terminals using CON-
SULT-III. Refer to
11.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is displayed, erase it. Refer to
EC-426, "Diagnosis Description"
>> GO TO 12.
12.
FINAL CHECK
When DTC was detected in step 2, perform DTC CONFIRMATION PROCEDURE or Component Function
Check again, and then make sure that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and make sure
that the symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 10.
YES-2 >> Symptom remains: GO TO 6.
NO
>> Before returning the vehicle to the customer, make sure to erase unnecessary DTC in ECM.
(Refer to
EC-426, "Diagnosis Description"
Diagnostic Work Sheet
INFOID:0000000001096724
DESCRIPTION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст