Nissan Qashqai (2007-2010). Manual — part 673
UPPER LINK
RSU-11
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UPPER LINK
Exploded View
INFOID:0000000000935955
Removal and Installation
INFOID:0000000000935956
REMOVAL
1.
Remove tires from vehicle.
2.
Set suitable jack under suspension arm to relieve the coil spring tension.
3.
Remove wheel sensor harness from suspension arm.
4.
Remove upper link from suspension arm.
5.
Remove upper link from suspension member.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform final tightening of rear suspension member and axle installation position (rubber bushing), under
unladen conditions with tires on level ground.
Inspection
INFOID:0000000000935957
INSPECTION AFTER REMOVAL
Check upper link and bushing for any deformation, cracks, or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust neutral position of steering angle sensor. Refer to
BRC-78, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
(with ESP).
2.
Check wheel alignment. Refer to
RSU-12
< ON-VEHICLE REPAIR >
REAR STABILIZER
REAR STABILIZER
Exploded View
INFOID:0000000000935958
Removal and Installation
INFOID:0000000000935959
REMOVAL
1.
Remove stabilizer link. Refer to
2.
Remove main muffler. Refer to
(MR20DE),
(K9K).
3.
Remove mounting nuts on stabilizer clamp and stabilizer bar from suspension member.
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000000935960
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer link, stabilizer bushing and stabilizer clamp for deformation, cracks or damage.
Replace it if necessary.
REAR SUSPENSION MEMBER
RSU-13
< ON-VEHICLE REPAIR >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000000935961
Removal and Installation
INFOID:0000000000935962
REMOVAL
1.
Remove tires from vehicle.
2.
Remove torque member mounting bolts. Hang torque member where it dose not interfere with work. Refer
to
BR-42, "BRAKE CALIPER ASSEMBLY : Exploded View"
(LHD),
CAUTION:
Never depressing brake pedal while brake caliper is removed.
3.
Remove disc rotor. Refer to
PB-7, "Removal and Installation"
4.
Remove wheel sensor and sensor harness from axle housing and lower link. Refer to
(with ABS),
BRC-172, "REAR WHEEL SENSOR : Exploded View"
(with ESP).
5.
Remove parking brake cable mounting bolts and separate parking brake cable from suspension arm.
Refer to
6.
Remove height sensor harness from lower link (with xenon head lamp). Refer to
.
7.
Remove main muffler. Refer to
(HR16DE),
(MR20DE),
(K9K).
8.
Remove stabilizer bar. Refer to
9.
Remove drive shaft. Refer to
.
10. Remove propeller shaft (4WD). Refer to
11. Remove rear final drive (4WD). Refer to
.
12. Remove shock absorber. Refer to
13. Remove coil spring. Refer to
14. Set suitable jack under rear suspension member.
15. Remove mounting nuts and bolts rear suspension member.
16. Slowly lower jack, then remove rear suspension member, lower link and upper link from vehicle as a unit.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
17. Remove mounting bolts and nuts, then remove lower link, and upper link from rear suspension member.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each parts removed when removing rear suspension assembly under unladen
conditions.
• Check wheel sensor harness for proper connection. Refer to
BRC-67, "REAR WHEEL SENSOR : Exploded
(with ABS),
BRC-172, "REAR WHEEL SENSOR : Exploded View"
(with ESP).
Inspection
INFOID:0000000000935963
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust neutral position of steering angle sensor. Refer to
BRC-78, "ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
(with ESP).
2.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
3.
Adjust parking brake operation. Refer to
PB-2, "Inspection and Adjustment"
.
RSU-14
< REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
REMOVAL AND INSTALLATION
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000000935964
Removal and Installation
INFOID:0000000001098343
1.
Rear suspension member
2.
Suspension member stay (right side) 3.
Suspension member stay (left side)
4.
Stabilizer bar
5.
Stabilizer bushing
6.
Stabilizer clamp
7.
Stabilizer link
8.
Suspension bar
9.
Suspension arm bracket
10. Suspension arm
11. Low rubber seat
12. Coil spring
13. Upper rubber seat
14. lower link
15. Upper link
16. Bound bumper
17. Shock absorber
: Vehicle body
Refer to
for symbols in the figure.
JPEIB0014GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст