Nissan Qashqai (2007-2010). Manual — part 1413
DIAGNOSIS SYSTEM (BCM)
INL-15
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000001116335
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
INT LAMP
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
INFOID:0000000001033372
Diagnosis mode
Function Description
WORK SUPPORT
Changes the setting for each system function.
SELF-DIAG RESULTS
Displays the diagnosis results judged by BCM. Refer to
CAN DIAG SUPPORT MNTR
Monitors the reception status of CAN communication viewed from BCM.
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
ECU IDENTIFICATION
The BCM part number is displayed.
CONFIGURATION
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
WORK SUPPORT
DATA MONITOR
ACTIVE TEST
—
BCM
×
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioner
AIR CONDITONER
×
Intelligent Key system
INTELLIGENT KEY
×
Combination switch
COMB SW
×
Immobilizer
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
Vehicle security system
THEFT ALM
×
×
×
Signal buffer system
SIGNAL BUFFER
×
×
PTC heater system
PTC HEATER
×
×
INL-16
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
WORK SUPPORT
*: Initial setting
DATA MONITOR
JPLIA0093GB
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
0 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 2
7.5 sec.
MODE 3*
15 sec.
MODE 4
30 sec.
SET I/L D-UNLCK INTCON
ON*
With the interior room lamp timer function
OFF
Without the interior room lamp timer function
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2*
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
4 sec.
MODE 6
5 sec.
MODE 7
0 sec.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door
only.
Monitor item
[Unit]
Description
IGN ON SW
[ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
ACC SW
[ON/OFF]
Ignition switch (ACC) status judges from ACC signal (ACC power supply)
DIAGNOSIS SYSTEM (BCM)
INL-17
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000001033373
WORK SUPPORT
*: Initial setting
DATA MONITOR
KEY ON SW
[ON/OFF]
The switch status input from key switch
PUSH SW
[ON/OFF]
Push switch status received from Intelligent Key unit by CAN communication
DOOR SW-DR
[ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS
[ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL
[ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW
[ON/OFF]
The switch status input from back door switch
CDL LOCK SW
[ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[ON/OFF]
Unlock switch status input from door lock and unlock switch
I-KEY LOCK
[ON/OFF]
Lock signal status received from Intelligent Key unit by CAN communication
I-KEY UNLOCK
[ON/OFF]
Unlock signal status received from Intelligent Key unit by CAN communication
KEYLESS LOCK
[ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK
[ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
ON
Outputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, personal lamp, room lamp, luggage room lamp (when applicable lamps
switch is in DOOR position.)]
OFF
Stops the interior room lamp control signal to turn the interior room lamps.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1*
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
INL-18
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
*: Each lamp switch is in ON position.
Monitor item
[Unit]
Description
IGN ON SW
[ON/OFF]
Ignition switch (ON) status judges from IGN signal (ignition power supply)
ACC SW
[ON/OFF]
Ignition switch (ACC) status judges from ACC signal (ACC power supply)
KEY ON SW
[ON/OFF]
The switch status input from key switch
PUSH SW
[ON/OFF]
Push switch status received from Intelligent Key unit by CAN communication
DOOR SW-DR
[ON/OFF]
The switch status input from front door switch (driver side)
DOOR SW-AS
[ON/OFF]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[ON/OFF]
The switch status input from rear door switch RH
DOOR SW- RL
[ON/OFF]
The switch status input from rear door switch LH
BACK DOOR SW
[ON/OFF]
The switch status input from back door switch
CDL LOCK SW
[ON/OFF]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[ON/OFF]
Unlock switch status input from door lock and unlock switch
I-KEY LOCK
[ON/OFF]
Lock signal status received from Intelligent Key unit by CAN communication
I-KEY UNLOCK
[ON/OFF]
Unlock signal status received from Intelligent Key unit by CAN communication
KEYLESS LOCK
[ON/OFF]
Lock signal status received from remote keyless entry receiver (integrated in the
BCM)
KEYLESS UNLOCK
[ON/OFF]
Unlock signal status received from remote keyless entry receiver (integrated in the
BCM)
Test item
Operation
Description
BATTERY SAVER
OFF
Cuts the interior room lamp power supply to turn interior room lamps OFF.
ON
Outputs the interior room lamp power supply to turn interior room lamps ON.*
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст