Nissan Qashqai (2007-2010). Manual — part 930
HAC-80
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
IN-VEHICLE SENSOR
IN-VEHICLE SENSOR
Description
INFOID:0000000000954664
In-vehicle Sensor
The in-vehicle sensor (1) is located on lower instrument panel, driver
side. It converts variations in temperature of compartment air drawn
from the aspirator into a resistance value. It is then input into the
auto amp.
In-vehicle Sensor Circuit
Aspirator
The aspirator (1) is located on driver’s side of A/C unit assembly. It
produces vacuum pressure due to air discharged from the A/C unit
assembly, continuously taking compartment air in the aspirator.
Component Function Check
INFOID:0000000000954665
1.
PERFORM SELF-DIAGNOSIS STEP-2
Perform self-diagnosis STEP-2. Refer to
HAC-27, "Diagnosis Description"
, see No. 1 to 3.
JPIIA0093ZZ
JPIIA0095GB
:
Vehicle front
JPIIA0029ZZ
JPIIA0094GB
IN-VEHICLE SENSOR
HAC-81
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
22 or –22 is displayed.
YES
>> Go to Diagnosis Procedure. Refer to
.
NO
>> END.
Diagnosis Procedure
INFOID:0000000000954666
1.
CHECK VOLTAGE BETWEEN IN-VEHICLE SENSOR AND GROUND
1.
Disconnect in-vehicle sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between in-vehicle sensor harness connector M41 terminal 1 and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK CIRCUIT CONTINUITY BETWEEN IN-VEHICLE SENSOR AND AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect auto amp. connector.
3.
Check continuity between in-vehicle sensor harness connector M41 terminal 2 and auto amp. harness
connector M53 terminal 26.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK IN-VEHICLE SENSOR
HAC-82, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace auto amp.
NO
>> Replace in-vehicle sensor.
4.
CHECK CIRCUIT CONTINUITY BETWEEN IN-VEHICLE SENSOR AND AUTO AMP.
1.
Turn ignition switch OFF.
2.
Disconnect auto amp. connector.
3.
Check continuity between in-vehicle sensor harness connector M41 terminal 1 and auto amp. harness
connector M53 terminal 27.
4.
Check continuity between in-vehicle sensor harness connector M41 terminal 1 and ground.
Is the inspection result normal?
(+)
(
−
)
Voltage
In-vehicle sensor
—
Connector
Terminal
M41
1
Ground
Approx. 5
In-vehicle sensor
Auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M41
2
M53
26
Continuity should exist
In-vehicle sensor
Auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M41
1
M53
27
Continuity should exist
In-vehicle sensor
—
Continuity
Connector
Terminal
M41
1
Ground
Continuity should not exist
HAC-82
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
IN-VEHICLE SENSOR
YES
>> Replace auto amp.
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000000954667
After disconnecting in-vehicle sensor (1) connector M41, measure
resistance between terminals 1 and 2 at sensor side. Refer to table
below.
If NG, replace in-vehicle sensor.
Temperature
°
C (
°
F)
Resistance k
Ω
−
15 (5)
12.73
−
10 (14)
9.92
−
5 (23)
7.80
0 (32)
6.19
5 (41)
4.95
10 (50)
3.99
15 (59)
3.24
20 (68)
2.65
25 (77)
2.19
30 (86)
1.81
35 (95)
1.51
40 (104)
1.27
45 (113)
1.07
JPIIA0096ZZ
SUNLOAD SENSOR
HAC-83
< COMPONENT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONER]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
SUNLOAD SENSOR
Description
INFOID:0000000000954668
COMPONENT DESCRIPTION
Sunload Sensor
The sunload sensor (1) is located on the tweeter grille (RH). It
detects sunload entering through windshield by means of a photo
diode. The sensor converts the sunload into a current value which is
then input into the auto amp.
Sunload Sensor Circuit
SUNLOAD INPUT PROCESS
The auto amp. also includes a processing circuit which averages the variations in detected sunload over a
period of time. This prevents drastic swings in the HAC system operation due to small or quick variations in
detected sunload.
For example, consider driving along a road bordered by an occasional group of large trees. The sunload
detected by the sunload sensor will vary whenever the trees obstruct the sunlight. The processing circuit aver-
ages the detected sunload over a period of time, so that the (insignificant) effect of the trees momentarily
obstructing the sunlight does not cause any change in the HAC system operation. On the other hand, shortly
after entering a long tunnel, the system will recognize the change in sunload, and the system will react accord-
ingly.
Component Function Check
INFOID:0000000000954669
1.
PERFORM SELF-DIAGNOSIS STEP-2
Perform self-diagnosis STEP-2. Refer to
HAC-27, "Diagnosis Description"
, see No. 1 to 3.
25 or
−
25 is displayed.
YES
>> Go to Diagnosis Procedure. Refer to
.
NO
>> END.
Diagnosis Procedure
INFOID:0000000000954670
1.
CHECK VOLTAGE BETWEEN SUNLOAD SENSOR AND GROUND
1.
Disconnect sunload sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between sunload sensor harness connector M74 terminal 1 and ground.
JPIIA0097ZZ
JPIIA0098GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст