Nissan Qashqai (2007-2010). Manual — part 1504
LAN
TROUBLE DIAGNOSIS
LAN-41
< FUNCTION DIAGNOSIS >
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Example: Data link connector branch line open circuit
NOTE:
• When data link connector branch line is open, transmission and reception of CAN communication signals
are not affected. Therefore, no symptoms occur. However, be sure to repair malfunctioning circuit.
• The model (all units on CAN communication system are Diag on CAN) cannot perform CAN diagnosis with
CONSULT-III if the following error occurs. The error is judged by the symptom.
EPS control unit
Normal operation.
Combination meter
• Shift position indicator and OD OFF indicator turn OFF.
• Warning lamps turn ON.
ABS actuator and electric unit (control unit)
Normal operation.
TCM
No impact on operation.
IPDM E/R
Normal operation.
Unit name
Symptom
SKIB8739E
Unit name
Symptom
ECM
Normal operation.
BCM
EPS control unit
Combination meter
ABS actuator and electric unit (control unit)
TCM
IPDM E/R
Error
Difference of symptom
Data link connector branch line open circuit
Normal operation.
CAN-H, CAN-L harness short-circuit
Most of the units which are connected to the CAN communication
system enter fail-safe mode or are deactivated.
LAN-42
< FUNCTION DIAGNOSIS >
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS
Example: Main Line Between Data Link Connector and ABS Actuator and Electric Unit (Control Unit) Open Circuit
Example: CAN-H, CAN-L Harness Short Circuit
SKIB8740E
Unit name
Symptom
ECM
Engine torque limiting is affected, and shift harshness increases.
BCM
• Reverse warning chime does not sound.
• The front wiper moves under continuous operation mode even though the front wip-
er switch being in the intermittent position.
EPS control unit
The steering effort increases.
Combination meter
• The shift position indicator and OD OFF indicator turn OFF.
• The speedometer is inoperative.
• The odo/trip meter stops.
ABS actuator and electric unit (control unit)
Normal operation.
TCM
No impact on operation.
IPDM E/R
When the ignition switch is ON,
• The headlamps (Lo) turn ON.
• The cooling fan continues to rotate.
SKIB8741E
LAN
TROUBLE DIAGNOSIS
LAN-43
< FUNCTION DIAGNOSIS >
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CAN Diagnosis with CONSULT-III
INFOID:0000000000892185
CAN diagnosis on CONSULT-III extracts the root cause by receiving the following information.
• Response to the system call
• Control unit diagnosis information
• Self-diagnosis
• CAN diagnostic support monitor
Self-Diagnosis
INFOID:0000000000892186
CAN Diagnostic Support Monitor
INFOID:0000000000892187
MONITOR ITEM (CONSULT-III)
Unit name
Symptom
ECM
• Engine torque limiting is affected, and shift harshness increases.
• Engine speed drops.
BCM
• Reverse warning chime does not sound.
• The front wiper moves under continuous operation mode even though the front
wiper switch being in the intermittent position.
• The room lamp does not turn ON.
• The engine does not start (if an error or malfunction occurs while turning the igni-
tion switch OFF.)
• The steering lock does not release (if an error or malfunction occurs while turning
the ignition switch OFF.)
EPS control unit
The steering effort increases.
Combination meter
• The tachometer and the speedometer do not move.
• Warning lamps turn ON.
• Indicator lamps do not turn ON.
ABS actuator and electric unit (control unit)
Normal operation.
TCM
No impact on operation.
IPDM E/R
When the ignition switch is ON,
• The headlamps (Lo) turn ON.
• The cooling fan continues to rotate.
DTC
Self-diagnosis item
(CONSULT-III indication)
DTC detection condition
Inspection/Action
U1000
CAN COMM CIRCUIT
When ECM is not transmitting or receiving CAN
communication signal of OBD (emission-related
diagnosis) for 2 seconds or more.
Start the inspection. Re-
fer to the applicable sec-
tion of the indicated
control unit.
When a control unit (except for ECM) is not
transmitting or receiving CAN communication
signal for 2 seconds or more.
U1001
CAN COMM CIRCUIT
When ECM is not transmitting or receiving CAN
communication signal other than OBD (emis-
sion-related diagnosis) for 2 seconds or more.
U1002
SYSTEM COMM
When a control unit is not transmitting or receiv-
ing CAN communication signal for 2 seconds or
less.
U1010
CONTROL UNIT [CAN]
When an error is detected during the initial diag-
nosis for CAN controller of each control unit.
Replace the control unit
indicating “U1010”.
LAN-44
< FUNCTION DIAGNOSIS >
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSIS
Example: CAN DIAG SUPPORT MNTR indication
Without PAST
With PAST
MONITOR ITEM (ON-BOARD DIAGNOSIS)
NOTE:
For some models, CAN communication diagnosis result is received from the vehicle monitor.
JSMIA0015GB
Item
PRSNT
Description
Initial diagnosis
OK
Normal at present
NG
Control unit error (Except for some control units)
Transmission diagnosis
OK
Normal at present
UNKWN
Unable to transmit signals for 2 seconds or more.
Diagnosis not performed
Control unit name
(Reception diagnosis)
OK
Normal at present
UNKWN
Unable to receive signals for 2 seconds or more.
Diagnosis not performed
No control unit for receiving signals. (No applicable optional parts)
Item
PRSNT
PAST
Description
Transmission diagnosis
OK
OK
Normal at present and in the past
1 – 39
Normal at present, but unable to transmit signals for 2 seconds or more
in the past. (The number indicates the number of ignition switch cycles
from OFF to ON.)
UNKWN
0
Unable to transmit signals for 2 seconds or more at present.
Control unit name
(Reception diagnosis)
OK
OK
Normal at present and in the past
1 – 39
Normal at present, but unable to receive signals for 2 seconds or more
in the past. (The number indicates the number of ignition switch cycles
from OFF to ON.)
UNKWN
0
Unable to receive signals for 2 seconds or more at present.
–
–
Diagnosis not performed.
No control unit for receiving signals. (No applicable optional parts)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст