Nissan Qashqai (2007-2010). Manual — part 681
BRAKE PIPING
BR-23
< ON-VEHICLE REPAIR >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT BRAKE (WITH ESP) : Removal and Installation
INFOID:0000000000938015
REMOVAL
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
1.
Remove tires.
2.
Drain brake fluid. Refer to
3.
Loosen the flare nut with a flare nut wrench and separate the brake tube from the hose.
CAUTION:
• Never scratch the flare nut and the brake tube.
• Never bend sharply, twist or strongly pull out the brake hoses and tubes.
• Cover open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.
4.
Remove the union bolt and remove the brake hose from the brake caliper assembly.
5.
Remove the lock plate and remove the brake hose.
INSTALLATION
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
1.
Assemble the union bolt and the copper washer to the brake hose.
CAUTION:
Never reuse the copper washer.
2.
Align the brake hose pin to the projection (A) of the brake caliper
assembly and tighten the union bolt (1) to the specified torque.
3.
Install the brake tube to the brake hose, temporarily tighten the
flare nut by hand until it does not rotate further, and fix the brake
hose to the bracket with the lock plate.
CAUTION:
Check that all brake hoses and tubes are not twisted and
bent.
4.
Tighten the flare nut to the specified torque with a flare nut
torque wrench.
CAUTION:
Never scratch the flare nut and the brake tube.
5.
Refill with new brake fluid and perform the air bleeding. Refer to
BR-12, "Bleeding Brake System"
.
CAUTION:
Never reuse drained brake fluid.
6.
Install tires.
FRONT BRAKE (WITH ESP) : Inspection
INFOID:0000000000938016
INSPECTION AFTER INSTALLATOIN
1.
Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no interfer-
ence with other components when steering the steering wheel; no looseness at connections.
2.
Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately
5 seconds with the engine running. Check for any fluid leakage.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Front disc brake
3.
Master cylinder assembly
4.
Brake booster
5.
Connector
6.
Rear disc brake
A.
Brake tube
B.
Brake hose
: Flare nut
: Union bolt
: Connector
JPFIA0099ZZ
BR-24
< ON-VEHICLE REPAIR >
[LHD]
BRAKE PIPING
CAUTION:
Retighten the applicable connection to the specified torque and repair any abnormal (damaged,
worn or deformed) part if any brake fluid leakage is present.
REAR BRAKE
REAR BRAKE : Exploded View
INFOID:0000000000925794
REAR BRAKE : Hydraulic Piping
INFOID:0000000000925795
1.
Brake tube
2.
Lock plate
3.
Brake hose
4.
Union bolt
A.
To front brake tube
B.
To rear brake hose
C.
Floor side
D.
Caliper side
Refer to
for symbols in the figure.
JPFIA0077GB
BRAKE PIPING
BR-25
< ON-VEHICLE REPAIR >
[LHD]
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR BRAKE : Removal and Installation
INFOID:0000000000925796
REMOVAL
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
1.
Remove tires.
2.
Drain brake fluid. Refer to
3.
Loosen the flare nut with a flare nut wrench and separate the brake tube from the hose.
CAUTION:
• Never scratch the flare nut and the brake tube.
• Never sharply bend, twist or strongly pull the brake hoses and tubes.
• Cover the open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.
4.
Remove the union bolt and remove the brake hose from the brake caliper assembly.
5.
Remove the lock plate and remove the brake hose from the vehicle.
INSTALLATION
CAUTION:
Never spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe it
off immediately and wash with water if it gets on a painted surface.
1.
Assemble the union bolt and the copper washer to the brake hose.
CAUTION:
Never reuse copper washer.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Front disc brake
3.
Master cylinder
4.
Brake booster
5.
Connector
6.
Rear disc brake
A.
Brake tube
B.
Brake hose
: Flare nut
: Union bolt
: Connector
JPFIA0078ZZ
BR-26
< ON-VEHICLE REPAIR >
[LHD]
BRAKE PIPING
2.
Install the brake hose L-pin by aligning it with the brake caliper
assembly positioning hole, and tighten the union bolt (1) to the
specified torque.
3.
Connect the hose to the brake tube, temporarily tighten the flare
nut by hand until it does not rotate further, and fix the brake hose
to the bracket with the lock plate.
CAUTION:
Check that the brake hoses and tubes are not twisted and
bent.
4.
Tighten the flare nut to the specified torque with a flare nut
torque wrench.
CAUTION:
Never scratch the flare nut and the brake tube.
5.
Refill with new brake fluid and perform the air bleeding. Refer to
BR-12, "Bleeding Brake System"
.
CAUTION:
Never reuse drained brake fluid.
6.
Install tires.
REAR BRAKE : Inspection
INFOID:0000000000925797
INSPECTION AFTER REMOVAL
1.
Check the brake hoses and tubes for the following: no scratches; no twist and deformation; no interfer-
ence with other components when steering the steering wheel; no looseness at connections.
2.
Depress the brake pedal with a force of 785 N (80 kg, 176 lb) and hold down the pedal for approximately
5 seconds with the engine running. Check for any fluid leakage.
CAUTION:
Retighten the applicable connection to the specified torque and repair any abnormal (damaged,
worn or deformed) part if any brake fluid leakage is present.
JPFIA0012ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст