Nissan Qashqai (2007-2010). Manual — part 717
BRC-66
< PREPARATION >
[ABS]
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000000925087
Tool number
Tool name
Description
GG94310000
Flare nut torque wrench
a: 10 mm (0.39 in)/ 12 mm (0.47 in)
Installing each brake piping
S-NT406
WHEEL SENSOR
BRC-67
< ON-VEHICLE REPAIR >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
ON-VEHICLE REPAIR
WHEEL SENSOR
FRONT WHEEL SENSOR
FRONT WHEEL SENSOR : Exploded View
INFOID:0000000001115319
NOTE:
The above figure (front side) shows left side. Right side is the mirror image.
FRONT WHEEL SENSOR : Removal and Installation
INFOID:0000000001115320
REMOVAL
Pay attention to the following when removing sensor.
CAUTION:
• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling
on sensor harness.
• Take care to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-
ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.
• When you see the harness of the wheel sensor from the front side of the vehicle ensure that the
white lines (A) are not twisted.
INSTALLATION
Pay attention to the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to
BRC-67, "FRONT WHEEL SENSOR : Exploded View"
• When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of the
wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign mate-
rial and clean the mount.
• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above
in the figure. When installed, harness must not be twisted.
REAR WHEEL SENSOR
REAR WHEEL SENSOR : Exploded View
INFOID:0000000001115321
1.
Front LH wheel sensor
A.
White line (slant line)
Refer to GI section
for symbols in the figure.
JSFIA0039GB
BRC-68
< ON-VEHICLE REPAIR >
[ABS]
WHEEL SENSOR
NOTE:
The above figure (front side) shows left side. Right side is the mirror image.
REAR WHEEL SENSOR : Removal and Installation
INFOID:0000000001115322
REMOVAL
Pay attention to the following when removing sensor.
CAUTION:
• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling
on sensor harness.
• Take care to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-
ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.
INSTALLATION
Pay attention to the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to
BRC-67, "REAR WHEEL SENSOR : Exploded View"
.
• When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of the
wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign mate-
rial and clean the mount.
• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above
in the figure. When installed, harness must not be twisted.
1.
Rear LH wheel sensor
A.
2WD models
B.
4WD models
Refer to GI section
for symbols in the figure.
JSFIA0040GB
SENSOR ROTOR
BRC-69
< ON-VEHICLE REPAIR >
[ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Exploded View
INFOID:0000000001115323
(2WD models),
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000001115324
REMOVAL
Sensor rotor cannot be disassembled. Remove the sensor rotor together with wheel hub and bearing assem-
bly. Refer to
FAX-9, "Removal and Installation"
FAX-49, "Removal and Installation"
(4WD mod-
els).
INSTALLATION
Sensor rotor cannot be disassembled. Installation the sensor rotor together with wheel hub and bearing
assembly. Refer to
FAX-9, "Removal and Installation"
FAX-49, "Removal and Installation"
(4WD models).
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Exploded View
INFOID:0000000001115325
(2WD models),
(4WD models).
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000001115326
2WD MODELS
Removal
Sensor rotor cannot be disassembled. Remove the sensor rotor together with wheel hub and bearing assem-
bly. Refer to
RAX-4, "Removal and Installation"
Installation
Sensor rotor cannot be disassembled. Installation the sensor rotor together with wheel hub and bearing
assembly. Refer to
RAX-4, "Removal and Installation"
.
4WD MODELS
For removal and installation of sensor rotor, refer to
RAX-14, "Disassembly and Assembly"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст