Nissan Qashqai (2007-2010). Manual — part 985
DLK-19
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR HINGE : Exploded View . . . . .
BACK DOOR HINGE : Removal and Installation ..
BACK DOOR STAY . . . . . . . . . . . .
BACK DOOR STAY : Exploded View . . . . ...
BACK DOOR STAY : Removal and Installation .
BACK DOOR WEATHER-STRIP . . . . . . .
BACK DOOR WEATHER-STRIP : Exploded View
BACK DOOR WEATHER-STRIP : Removal and
Installation . . . . . . . . . . . . . . . .
FRONT DOOR LOCK . . . . . . . . . ...
DOOR LOCK . . . . . . . . . . . . . . ...
DOOR LOCK : Exploded View . . . . . . . ..
DOOR LOCK : Removal and Installation . . . ..
INSIDE HANDLE . . . . . . . . . . . . . .
INSIDE HANDLE : Exploded View . . . . . .
INSIDE HANDLE : Removal and Installation . .
OUTSIDE HANDLE . . . . . . . . . . . . .
OUTSIDE HANDLE : Exploded View . . . . .
OUTSIDE HANDLE : Removal and Installation .
REAR DOOR LOCK . . . . . . . . . . .
DOOR LOCK . . . . . . . . . . . . . . ...
DOOR LOCK : Exploded View . . . . . . . ..
DOOR LOCK : Removal and Installation . . . ..
INSIDE HANDLE . . . . . . . . . . . . . .
INSIDE HANDLE : Exploded View . . . . . .
INSIDE HANDLE : Removal and Installation . .
OUTSIDE HANDLE . . . . . . . . . . . . ..
OUTSIDE HANDLE : Exploded View . . . . .
OUTSIDE HANDLE : Removal and Installation . .
BACK DOOR LOCK . . . . . . . . . ...
DOOR LOCK . . . . . . . . . . . . . . .
DOOR LOCK : Exploded View . . . . . . . ..
DOOR LOCK : Removal and Installation . . . ...
FUEL FILLER LID OPENER . . . . . . ...
FUEL FILLER LID . . . . . . . . . . . . .
FUEL FILLER LID : Exploded View . . . . . ...
FUEL FILLER LID : Removal and Installation . ...
FUEL FILLER OPENER CABLE . . . . . . . .
FUEL FILLER OPENER CABLE : Exploded View ..
FUEL FILLER OPENER CABLE : Removal and
Installation . . . . . . . . . . . . . . . .
DOOR SWITCH . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
BACK DOOR OPENER SWITCH . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
KEYFOB BATTERY . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
DLK-20
< BASIC INSPECTION >
[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000000939032
OVERALL SEQUENCE
DETAILED FLOW
JMKIA0101GB
DIAGNOSIS AND REPAIR WORKFLOW
DLK-21
< BASIC INSPECTION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC for Intelligent Key unit and BCM.
2.
Perform the following procedure if DTC is displayed.
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real-time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to
DLK-163, "DTC Inspection Priority Chart"
(Intelligent Key unit),
DLK-201, "DTC Inspection Priority Chart"
(BCM) and determine trouble diagnosis order.
Is DTC detected?
YES
>> GO TO 8.
NO
>> Refer to
GI-39, "Intermittent Incident"
.
6.
PERFORM BASIC INSPECTION
Perform Basic Inspection. Refer to
>> GO TO 7.
7.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to Symptom Table based on the confirmed symptom in step 4.
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure is described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 9.
DLK-22
< BASIC INSPECTION >
[WITH I-KEY, WITHOUT SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
9.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
10.
FINAL CHECK
When DTC was detected in step 9, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunctions have been fully repaired.
When symptom was described by the customer, refer to the confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст