Nissan Qashqai (2007-2010). Manual — part 397
P0340 CMP SENSOR (PHASE)
EC-1107
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace camshaft position sensor (PHASE).
Terminals (Polarity)
Resistance [at 25
°
C (77
°
F)]
1 (+) - 2 (-)
Except 0 or
∞
Ω
1 (+) - 3 (-)
2 (+) - 3 (-)
EC-1108
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
P0605 ECM
P0605 ECM
Description
INFOID:0000000001094179
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC Logic
INFOID:0000000001094180
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1.
Turn ignition switch ON.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1112, "Diagnosis Procedure"
.
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1112, "Diagnosis Procedure"
.
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Repeat step 2 for 32 times.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1112, "Diagnosis Procedure"
.
NO
>> INSPECTION END
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
P0605 ECM
EC-1109
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Diagnosis Procedure
INFOID:0000000001094181
1.
INSPECTION START
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE.
See
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Erase the diagnostic Test Mode II (Self-diagnostic results) memory.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
Is the 1st trip DTC P0605 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
EC-989, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
.
>> INSPECTION END
EC-1110
< COMPONENT DIAGNOSIS >
[MR20DE (WITHOUT EURO-OBD)]
P1111 IVT CONTROL SOLENOID VALVE
P1111 IVT CONTROL SOLENOID VALVE
Description
INFOID:0000000001094182
Intake valve timing control solenoid valve is activated by ON/OFF
pulse duty (ratio) signals from the ECM.
The intake valve timing control solenoid valve changes the oil
amount and direction of flow through intake valve timing control unit
or stops oil flow.
The longer pulse width advances valve angle.
The shorter pulse width retards valve angle.
When ON and OFF pulse widths become equal, the solenoid valve
stops oil pressure flow to fix the intake valve angle at the control
position.
DTC Logic
INFOID:0000000001094183
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 5 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
EC-1113, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001094184
1.
CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect intake valve timing control solenoid valve harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between intake valve timing control solenoid valve harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTION PART
PBIB1842E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1111
Intake valve timing control
solenoid valve circuit
An improper voltage is sent to the ECM
through intake valve timing control solenoid
valve.
• Harness or connectors
(Intake valve timing control solenoid valve
circuit is open or shorted.)
• Intake valve timing control solenoid valve
IVT control solenoid valve
Ground
Voltage
Connector
Terminal
F41
2
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст