Nissan Qashqai (2007-2010). Manual — part 1316
MIR-10
< COMPONENT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch. Refer to
MIR-41, "Removal and Installation"
OPEN/CLOSE SWITCH
OPEN/CLOSE SWITCH : Description
INFOID:0000000000951524
• Open/close switch is interacted into door mirror control switch.
• Power is supplied to folding motor located inside the door mirror to operate the mirror.
OPEN/CLOSE SWITCH : Component Function Check
INFOID:0000000000951525
1.
CHECK OPEN/CLOSE SWITCH FUNCTION
Check that door mirror can operate by door mirror remote control switch (open/close switch) operation.
Is the inspection result normal?
YES
>> Open / close switch function is OK.
NO
>> Refer to
MIR-10, "OPEN/CLOSE SWITCH : Diagnosis Procedure"
OPEN/CLOSE SWITCH : Diagnosis Procedure
INFOID:0000000000951526
1.
CHECK OPEN / CLOSE SWITCH OUTPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror remote control switch and ground.
Is the inspection result normal?
YES
>> Open/close switch function is OK.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between door mirror remote control switch and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch connector and ground.
Is the inspection result normal?
(+)
(-)
Open / close switch condition
Voltage (V)
(Approx.)
Door mirror remote control switch connector
Terminal
M7
8
Ground
CLOSE
Battery voltage
Other than above
0
9
OPEN
Battery voltage
Other than above
0
(+)
(-)
Voltage (V)
(Approx.)
Door mirror remote control switch connector
Terminal
M7
3
Ground
Battery voltage
Door mirror remote control switch connector
Terminal
Ground
Continuity
M7
1
Existed
DOOR MIRROR REMOTE CONTROL SWITCH
MIR-11
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK OPEN/CLOSE SWITCH
Check open/close switch.
Refer to
MIR-11, "OPEN/CLOSE SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> Refer to
GI-39, "Intermittent Incident"
NO
>> Replace door mirror remote control switch. Refer to
MIR-41, "Removal and Installation"
OPEN/CLOSE SWITCH : Component Inspection
INFOID:0000000000951527
1.
CHECK OPEN/CLOSE SWITCH
Check door mirror remote control switch.
Power supply
Ground
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror remote control switch. Refer to
MIR-41, "Removal and Installation"
Terminal
Open/close switch condition
Continuity
Door mirror remote control switch
8
3
CLOSE
Existed
Other than above
Not existed
9
OPEN
Existed
Other than above
Not existed
Terminal
Open/close switch condition
Continuity
Door mirror remote control switch
8
1
OPEN
Existed
Other than above
Not existed
9
CLOSE
Existed
Other than above
Not existed
MIR-12
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
DOOR MIRROR MOTOR
Description
INFOID:0000000000951520
It supplies electric power to door mirror motor with mirror switch and changeover switch.
Component Function Check
INFOID:0000000000951521
1.
CHECK DOOR MIRROR MOTOR FUNCTION
Does motor operate normally during mirror switch operation.
Is the inspection result normal?
YES
>> Door mirror motor function is OK.
NO
>> Refer to
Diagnosis Procedure
INFOID:0000000000951522
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector and door mirror connector.
3.
Check continuity between door mirror remote control switch connector and door mirror connector.
-
LHD models
[Door mirror driver side]
[Door mirror passenger side]
Terminals
Mirror switch
Condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector
Terminal
LHD models
D3 (Driver side) / D43 (Passenger side)
RHD models
D23 (Driver side) / D63 (Passenger side)
2
Ground
LEFT
Battery voltage
Other than above
0
3
UP
Battery voltage
Other than above
0
4
DOWN / RIGHT
Battery voltage
Other than above
0
Door mirror remote control
switch connector
Terminal
Door mirror connector
Terminal
Continuity
M7
2
D3
4
Existed
6
2
7
3
Door mirror remote control
switch connector
Terminal
Door mirror connector
Terminal
Continuity
M7
2
D43
4
Existed
4
2
5
3
DOOR MIRROR MOTOR
MIR-13
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
RHD models
[Door mirror driver side]
[Door mirror passenger side]
4.
Check continuity between automatic drive positioner control unit connector and ground.
LHD models
[Door mirror driver side]
[Door mirror passenger side]
RHD models
[Door mirror driver side]
[Door mirror passenger side]
Is the inspection result normal?
YES
>> Refer to
GI-39, "Intermittent Incident"
.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to
MIR-14, "Component Inspection"
Is the inspection result normal?
YES
>> Refer to
GI-39, "Intermittent Incident"
Door mirror remote control
switch connector
Terminal
Door mirror connector
Terminal
Continuity
M7
2
D23
4
Existed
4
2
5
3
Door mirror remote control
switch connector
Terminal
Door mirror connector
Terminal
Continuity
M7
2
D63
4
Existed
6
2
7
3
Door mirror remote control switch con-
nector
Terminal
Ground
Continuity
M7
2
Not existed
6
7
Door mirror remote control switch con-
nector
Terminal
Ground
Continuity
M7
2
Not existed
4
5
Door mirror remote control switch con-
nector
Terminal
Ground
Continuity
M7
2
Not existed
4
5
Door mirror remote control switch con-
nector
Terminal
Ground
Continuity
M7
2
Not existed
6
7
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст