Nissan Qashqai (2007-2010). Manual — part 192
P2135 TP SENSOR
EC-287
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Turn ignition switch ON.
3.
Check the voltage between electric throttle control actuator harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK THROTTLE POSITION SENSOR POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between electric throttle control actuator harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit.
4.
CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between electric throttle control actuator harness connector and ground.
4.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK THROTTLE POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between electric throttle control actuator harness connector and ground.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair open circuit or short to ground or short to power in harness or connectors.
6.
CHECK THROTTLE POSITION SENSOR
EC-289, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 7.
Electric throttle control actuator
Ground
Voltage
Connector
Terminal
F29
1
Ground
Approx. 5V
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
1
F8
72
Existed
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
4
F8
36
Existed
Electric throttle control actuator
ECM
Continuity
Connector
Terminal
Connector
Terminal
F29
2
F8
33
Existed
3
34
EC-288
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P2135 TP SENSOR
7.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator.
2.
EC-289, "Special Repair Requirement"
>> INSPECTION END
8.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000001056475
1.
CHECK THROTTLE POSITION SENSOR
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
EC-289, "Special Repair Requirement"
4.
Turn ignition switch ON.
5.
Set shift lever to 1st position.
6.
Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1.
Replace electric throttle control actuator.
2.
Go to
EC-289, "Special Repair Requirement"
.
>> INSPECTION END
Special Repair Requirement
INFOID:0000000001056476
1.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-31, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
>> GO TO 2.
2.
PERFORM IDLE AIR VOLUME LEARNING
EC-31, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
ECM
Ground
Condition
Voltage
Connector
Terminal
F8
33
(TP sensor 1 signal)
Ground
Accelerator pedal
Fully released
More than 0.36V
Fully depressed
Less than 4.75V
34
(TP sensor 2 signal)
Fully released
Less than 4.75V
Fully depressed
More than 0.36V
P2138 APP SENSOR
EC-289
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P2138 APP SENSOR
Description
INFOID:0000000001056477
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensor detects the accelera-
tor position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors
are a kind of potentiometers which transform the accelerator pedal
position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of
the accelerator pedal and feed the voltage signals to the ECM. The
ECM judges the current opening angle of the accelerator pedal from
these signals and controls the throttle control motor based on these
signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine oper-
ation such as fuel cut.
DTC Logic
INFOID:0000000001056478
DTC DETECTION LOGIC
NOTE:
If DTC P2138 is displayed with DTC P1229, first perform the trouble diagnosis for DTC P1229. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 10V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine and let it idle for 1 second.
2.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001056479
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
PBIB1741E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2138
Accelerator pedal posi-
tion sensor circuit range/
performance
Rationally incorrect voltage is sent to ECM
compared with the signals from APP sensor 1
and APP sensor 2.
• Harness or connector
(APP sensor 1 and 2 circuit is open or
shorted.)
[Crankshaft position sensor (POS) circuit
is shorted.)
(Refrigerant pressure sensor circuit is
shorted.)
• Accelerator pedal position sensor
(APP sensor 1 and 2)
• Crankshaft position sensor (POS)
• Refrigerant pressure sensor
EC-290
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P2138 APP SENSOR
2.
Check ground connection E21. Refer to Ground Inspection in
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT
1.
Disconnect accelerator pedal position (APP) sensor harness connector.
2.
Turn ignition switch ON.
3.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit or short to ground or shot to power in harness or connectors.
3.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch ON.
2.
Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 4.
4.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-II
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Check the continuity between APP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair open circuit or short to ground or shot to power in harness or connectors.
5.
CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-III
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair short to ground or short to power in harness or connectors.
6.
CHECK COMPONENTS
APP sensor
Ground
Voltage
Connector
Terminal
E110
4
Ground
Approx. 5V
APP sensor
Ground
Voltage
Connector
Terminal
E110
5
Ground
Approx. 5V
APP sensor
ECM
Continuity
Connector
Terminal
Connector
Terminal
E110
5
E16
102
Existed
ECM
Sensor
Connector
Terminal
Item
Connector
Terminal
F8
74
Refrigerant pressure sensor
E49
3
75
CKP sensor (POS)
F20
1
E16
102
APP sensor
E110
5
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст