Nissan Pathfinder (2010 year). Instruction — part 614
TM-40
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (TCM)
HLR/C SOL (A)
—
X
ON OFF SOL (ON-OFF display)
—
—
LC/B solenoid
TCC SOL MON (A)
—
—
L/P SOL MON (A)
—
—
I/C SOL MON (A)
—
—
FR/B SOL MON (A)
—
—
D/C SOL MON (A)
—
—
HLR/C SOL MON (A)
—
—
ONOFF SOL MON (ON-OFF display)
—
—
LC/B solenoid
P POSI IND (ON-OFF display)
—
—
R POSI IND (ON-OFF display)
—
—
N POSI IND (ON-OFF display)
—
—
D POSI IND (ON-OFF display)
—
—
4TH POSI IND (ON-OFF display)
—
—
3RD POSI IND (ON-OFF display)
—
—
2ND POSI IND (ON-OFF display)
—
—
1ST POSI IND (ON-OFF display)
—
—
MANU MODE IND (ON-OFF display)
—
—
POWER M LAMP (ON-OFF display)
—
—
F-SAFE IND/L (ON-OFF display)
—
—
ATF WARN LAMP (ON-OFF display)
—
—
BACK-UP LAMP (ON-OFF display)
—
—
STARTER RELAY (ON-OFF display)
—
—
RANGE SW3 MON (ON-OFF display)
—
—
C/V CLB ID1
—
—
C/V CLB ID2
—
—
C/V CLB ID3
—
—
UNIT CLB ID1
—
—
UNIT CLB ID2
—
—
UNIT CLB ID3
—
—
TRGT GR RATIO
—
—
TRGT PRES TCC (kPa, kg/cm
2
or psi)
—
—
TRGT PRES L/P (kPa, kg/cm
2
or psi)
—
—
TRGT PRES I/C (kPa, kg/cm
2
or psi)
—
—
TRGT PRE FR/B (kPa, kg/cm
2
or psi)
—
—
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG-
NALS
MAIN SIG-
NALS
SELEC-
TION
FROM
MENU
2010 Pathfinder
DIAGNOSIS SYSTEM (TCM)
TM-41
< FUNCTION DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DTC & SRT CONFIRMATION
DTC Work Support Mode
Diagnosis Procedure without CONSULT-III
INFOID:0000000005257968
OBD-II SELF-DIAGNOSTIC PROCEDURE (WITH GST)
EC-86, "Generic Scan Tool (GST) Function"
EC-564, "Generic Scan Tool (GST) Func-
(VK56DE).
OBD-II SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
TM-35, "Malfunction Indicator Lamp (MIL)"
.
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS) — WITH MANUAL MODE
Description
TRGT PRES D/C (kPa, kg/cm
2
or psi)
—
—
TRG PRE HLR/C (kPa, kg/cm
2
or psi)
—
—
SHIFT PATTERN
—
—
DRV CST JUDGE
—
—
START RLY MON
—
—
NEXT GR POSI
—
—
SHIFT MODE
—
—
MANU GR POSI
—
—
VEHICLE SPEED (km/h or mph)
—
X
Vehicle speed recognized by the TCM.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG-
NALS
MAIN SIG-
NALS
SELEC-
TION
FROM
MENU
DTC work support item
Description
Check item
1ST GR FNCTN P0731
Following items for “1GR incorrect ratio” can be confirmed.
• Self-diagnosis status (whether the diagnosis is being performed
or not)
• Self-diagnostic results (OK or NG)
• Input clutch solenoid valve
• Front brake solenoid valve
• Direct clutch solenoid valve
• High and low reverse clutch
solenoid valve
• Each clutch and brake
• Hydraulic control circuit
2ND GR FNCTN P0732
Following items for “2GR incorrect ratio” can be confirmed.
• Self-diagnosis status (whether the diagnosis is being performed
or not)
• Self-diagnostic results (OK or NG)
3RD GR FNCTN P0733
Following items for “3GR incorrect ratio” can be confirmed.
• Self-diagnosis status (whether the diagnosis is being performed
or not)
• Self-diagnostic results (OK or NG)
4TH GR FNCTN P0734
Following items for “4GR incorrect ratio” can be confirmed.
• Self-diagnosis status (whether the diagnosis is being performed
or not)
• Self-diagnostic results (OK or NG)
5TH GR FNCTN P0735
Following items for “5GR incorrect ratio” can be confirmed.
• Self-diagnosis status (whether the diagnosis is being performed
or not)
• Self-diagnostic results (OK or NG)
2010 Pathfinder
TM-42
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (TCM)
When the ignition switch is switched “ON”, the A/T CHECK indicator lamp lights up for 2 seconds. As a method
for locating the suspect circuit, when the self-diagnostics start signal is input, the memory for the malfunction
location is output and the A/T CHECK indicator lamp flashes to display the corresponding DTC.
Diagnostic Procedure
1.
CHECK A/T CHECK INDICATOR LAMP
1. Start the engine with selector lever in “P” position. Warm engine to normal operating temperature.
2. Turn ignition switch ON and OFF at least twice, then leave it in the OFF position.
3. Wait 10 seconds.
4. Turn ignition switch ON. (Do not start engine.)
Does A/T CHECK indicator lamp come on for about 2 seconds?
YES
>> GO TO 2.
NO
>> Go to
.
2.
JUDGMENT PROCEDURE STEP 1
1. Turn ignition switch OFF.
2. Keep pressing shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Release accelerator pedal. (Set the closed throttle position signal “ON”.)
5. Depress brake pedal. (Stop lamp switch signal “ON”.)
6. Turn ignition switch ON (Do not start engine.)
7. Wait 3 seconds.
8. Move the selector lever to the instruction shift gate side. (Instruction mode signal “ON”.)
9. Release brake pedal. (Stop lamp switch signal “OFF”.)
10. Move the selector lever to “D” position. (Instruction mode signal ON.)
11. Depress brake pedal. (Stop lamp switch signal “ON”.)
12. Release brake pedal. (Stop lamp switch signal “OFF”.)
13. Depress accelerator pedal fully and release it.
>> GO TO 3.
3.
CHECK SELF-DIAGNOSIS CODE
Check A/T CHECK indicator lamp.
Refer to “Judgement Self-diagnosis Code”.
If the system does not go into self-diagnostics. Refer to
,
,
.
>>
DIAGNOSIS END
Judgment Self-diagnosis Code
2010 Pathfinder
DIAGNOSIS SYSTEM (TCM)
TM-43
< FUNCTION DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
If there is a malfunction, the lamp lights up for the time corresponding to the suspect circuit.
Erase Self-diagnosis
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.
• However, this information is erased by turning ignition switch OFF after executing self-diagnostics or by
erasing the memory using the CONSULT-III.
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS) — WITHOUT MANUAL MODE
Description
When the ignition switch is switched “ON”, the O/D OFF indicator lamp lights up for 2 seconds. As a method
for locating the suspect circuit, when the self-diagnostics start signal is input, the memory for the malfunction
location is output and the O/D OFF indicator lamp flashes to display the corresponding DTC.
JPDIA0024GB
No.
Malfunctioning item
No.
Malfunctioning item
1
Output speed sensor
12
Interlock
2
Direct clutch solenoid
13
1st engine braking
3
Torque converter
14
4
Line pressure solenoid
15
TP sensor
5
Input clutch solenoid
16
Engine speed
6
Front brake solenoid
17
CAN communication line
7
18
1GR incorrect ratio
8
High and low reverse clutch solenoid
19
2GR incorrect ratio
9
Transmission range switch
20
3GR incorrect ratio
10
Transmission fluid temperature sensor
21
4GR incorrect ratio
11
Input speed sensor
22
5GR incorrect ratio
2010 Pathfinder
TM-44
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (TCM)
Diagnostic Procedure
1.
CHECK O/D OFF INDICATOR LAMP
1. Start the engine with selector lever in “P” position. Warm engine to normal operating temperature.
2. Turn ignition switch ON and OFF at least twice, then leave it in the OFF position.
3. Wait 10 seconds.
4. Turn ignition switch ON. (Do not start engine.)
Does O/D OFF indicator lamp come on for about 2 seconds?
YES
>> GO TO 2.
NO
>> Go to
.
2.
JUDGMENT PROCEDURE STEP 1
1. Turn ignition switch OFF.
2. Keep pressing shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Release accelerator pedal. (Set the closed throttle position signal “ON”.)
5. Depress brake pedal. (Stop lamp switch signal “ON”.)
6. Turn ignition switch ON. (Do not start engine.)
7. Wait 3 seconds.
8. Move the selector lever from “D” to “3” position.
9. Release brake pedal. (Stop lamp switch signal “OFF”.)
10. Move the selector lever from “3” to “2” position.
11. Depress brake pedal. (Stop lamp switch signal “ON”.)
12. Depress accelerator pedal fully and release it.
>> GO TO 3.
3.
CHECK SELF-DIAGNOSIS CODE
Check O/D OFF indicator lamp.
Refer to “Judgement Self-diagnosis Code”.
If the system does not go into self-diagnostics. Refer to
,
,
>>
DIAGNOSIS END
Judgment Self-diagnosis Code
2010 Pathfinder
DIAGNOSIS SYSTEM (TCM)
TM-45
< FUNCTION DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
If there is a malfunction, the lamp lights up for the time corresponding to the suspect circuit.
Erase Self-diagnosis
• In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is
stored into the control unit as necessary during use by the user. This memory is not erased no matter how
many times the ignition switch is turned ON and OFF.
• However, this information is erased by turning ignition switch OFF after executing self-diagnostics or by
erasing the memory using the CONSULT-III.
JSDIA1433GB
No.
Malfunctioning item
No.
Malfunctioning item
1
Output speed sensor
12
Interlock
2
Direct clutch solenoid
13
1st engine braking
3
Torque converter
14
4
Line pressure solenoid
15
TP sensor
5
Input clutch solenoid
16
Engine speed
6
Front brake solenoid
17
CAN communication line
7
18
1GR incorrect ratio
8
High and low reverse clutch solenoid
19
2GR incorrect ratio
9
Transmission range switch
20
3GR incorrect ratio
10
Transmission fluid temperature sensor
21
4GR incorrect ratio
11
Input speed sensor
22
5GR incorrect ratio
2010 Pathfinder
TM-46
< COMPONENT DIAGNOSIS >
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000005257969
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent malfunction detection ability.
Many electronic control units are equipped onto a vehicle, and each control unit shares information and links
with other control units during operation (not independent). In CAN communication, control units are con-
nected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission
with less wiring. Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis Logic
INFOID:0000000005257970
• This is an OBD-II self-diagnostic item.
• Diagnostic trouble code “U1000” with CONSULT-III or 17th judgment flicker without CONSULT-III is detected
when TCM cannot communicate to other control units.
Possible Cause
INFOID:0000000005257971
Harness or connectors
(CAN communication line is open or shorted.)
DTC Confirmation Procedure
INFOID:0000000005257972
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Turn ignition switch “ON”. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with CONSULT-III.
3. Start engine and wait for at least 6 seconds.
4. If DTC is detected, go to
WITH GST
Follow the procedure “WITH CONSULT-III”.
Diagnosis Procedure
INFOID:0000000005257973
1.
CHECK CAN COMMUNICATION CIRCUIT
With CONSULT-III
1. Turn ignition switch “ON” and start engine.
2. Select “SELF-DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-III.
Is any malfunction of the “U1000” indicated?
YES
>> Go to LAN section. Refer to
LAN-14, "Trouble Diagnosis Flow Chart"
.
NO
>>
INSPECTION END
2010 Pathfinder
P0615 STARTER RELAY
TM-47
< COMPONENT DIAGNOSIS >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
P0615 STARTER RELAY
Description
INFOID:0000000005257974
• TCM prohibits cranking other than at “P” or “N” position.
CONSULT-III Reference Value in Data Monitor Mode
INFOID:0000000005257975
On Board Diagnosis Logic
INFOID:0000000005257976
• This is not an OBD-II self-diagnostic item.
• Diagnostic trouble code “P0615” with CONSULT-III or 14th judgment flicker without CONSULT-III is detected
when starter relay is switched “ON” other than at “P” or “N” position. (Or when switched “OFF” at “P” or “N”
position).
Possible Cause
INFOID:0000000005257977
• Harness or connectors
(The starter relay and TCM circuit is open or shorted.)
• Starter relay
DTC Confirmation Procedure
INFOID:0000000005257978
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch “OFF”
and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-III
1. Shift selector lever to “P” or “N” position.
2. Turn ignition switch ON and wait for at least 2 seconds.
3. Select “SELF-DIAG RESULTS” mode for “TRANSMISSION” with CONSULT-III.
4. If DTC is detected, go to
Diagnosis Procedure
INFOID:0000000005257979
1.
CHECK STARTER RELAY
With CONSULT-III
1. Turn ignition switch ON. (Do not start engine.)
2. Select “SELECTION FROM MENU” in “DATA MONITOR” mode for "TRANSMISSION" with CONSULT-III
and check monitor “STARTER RELAY” ON/OFF.
Without CONSULT-III
1. Turn ignition switch ON. (Do not start engine.)
2. Check voltage between the IPDM E/R connector and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
Item name
Condition
Display value
STARTER RELAY
Selector lever in “N”, “P” positions.
ON
Selector lever in other position.
OFF
Item
Connector
Terminal
Shift position
Voltage (Ap-
prox.)
Starter relay
E122
48
Ground
“N” and “P”
Battery voltage
“R” and “D”
0V
LCIA0320E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст