Nissan Pathfinder (2010 year). Instruction — part 542
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPERATE
PROPERLY
PWC-89
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
POWER WINDOW RETAINED POWER OPERATION DOES NOT OPER-
ATE PROPERLY
Diagnosis Procedure
INFOID:0000000005256068
1.
CHECK FRONT DOOR SWITCH
Check front door switch.
PWC-33, "Component Function Check"
.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-37, "Intermittent Incident"
.
2010 Pathfinder
PWC-90
< SYMPTOM DIAGNOSIS >
DOES NOT OPERATE BY KEY CYLINDER SWITCH
DOES NOT OPERATE BY KEY CYLINDER SWITCH
Diagnosis Procedure
INFOID:0000000005256069
1.
CHECK FRONT DOOR LOCK ASSEMBLY LH (KEY CYLINDER SWITCH)
Check front door lock assembly LH (key cylinder switch).
PWC-35, "Component Function Check"
.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-37, "Intermittent Incident"
.
2010 Pathfinder
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
PWC-91
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
KEYLESS POWER WINDOW DOWN DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000005256070
1.
CHECK INTELLIGENT KEY OR KEYFOB FUNCTION
Check Intelligent Key or keyfob function.
Refer to
BCS-25, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
with Intelligent
Key or
BCS-20, "MULTIREMOTE ENT : CONSULT-III Function (BCM - MULTIREMOTE ENT)"
with remote
keyless entry system.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-37, "Intermittent Incident"
.
NO
>> Replace BCM. Refer to
BCS-59, "Removal and Installation"
2010 Pathfinder
PWC-92
< SYMPTOM DIAGNOSIS >
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
POWER WINDOW LOCK SWITCH DOES NOT FUNCTION
Diagnosis Procedure
INFOID:0000000005256071
1.
REPLACE MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Replace main power window and door lock/unlock switch.
PWC-95, "Removal and Installation"
.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Check intermittent incident. Refer to
GI-37, "Intermittent Incident"
.
2010 Pathfinder
PRECAUTIONS
PWC-93
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000005519259
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Instruction. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000005256073
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″
LOCK
″
position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the
″
ACC
″
position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.
2010 Pathfinder
PWC-94
< PRECAUTION >
PRECAUTIONS
5. When the repair work is completed, return the ignition switch to the
″
LOCK
″
position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.)
6. Perform a self-diagnosis check of all control units using CONSULT-III.
2010 Pathfinder
POWER WINDOW MAIN SWITCH
PWC-95
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
PWC
N
O
P
ON-VEHICLE REPAIR
POWER WINDOW MAIN SWITCH
Removal and Installation
INFOID:0000000005256074
REMOVAL
1. Remove the power window main switch finisher (2) from the
front door finisher LH. Refer to
INT-14, "Removal and Installa-
2. Remove the three screws (A) from the power window main
switch (1), then separate from the finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
Pawl
Metal clip
ALKIA1097ZZ
2010 Pathfinder
PWC-96
< ON-VEHICLE REPAIR >
FRONT POWER WINDOW SWITCH
FRONT POWER WINDOW SWITCH
Removal and Installation
INFOID:0000000005256075
REMOVAL
1. Remove the front power window switch finisher (2) from the front
door finisher RH. Refer to
INT-14, "Removal and Installation"
.
2. Release the four tabs (A), two on each side, then separate the
front power window switch (1) from the finisher (2).
INSTALLATION
Installation is in the reverse order of removal.
Pawl
Metal clip
ALKIA1098ZZ
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст