Nissan Pathfinder (2010 year). Instruction — part 274
EC-284
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0456 EVAP CONTROL SYSTEM
2. Does water drain from the EVAP canister?
Yes or No
Yes
>> GO TO 10.
No (With CONSULT-III)>>GO TO 12.
No (Without CONSULT-III)>>GO TO 13.
10.
CHECK EVAP CANISTER
Weigh the EVAP canister with the EVAP canister vent control valve and EVAP control system pressure sensor
attached.
The weight should be less than 2.0 kg (4.4 lb).
OK or NG
OK (With CONSULT-III)>>GO TO 12.
OK (Without CONSULT-III)>>GO TO 13.
NG
>> GO TO 11.
11.
DETECT MALFUNCTIONING PART
Check the following.
• EVAP canister for damage
• EVAP hose between EVAP canister and vehicle frame for clogging or poor connection
>> Repair hose or replace EVAP canister.
12.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
With CONSULT-III
1. Disconnect vacuum hose connected to EVAP service port and EVAP canister purge volume control sole-
noid valve from EVAP canister purge volume control solenoid valve.
2. Start engine.
3. Perform “PURG VOL CONT/V” in “ACTIVE TEST” mode.
4. Touch “Qu” on CONSULT-III screen to increase “PURG VOL CONT/V” opening to 100%.
5. Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 16.
NG
>> GO TO 14.
13.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE OPERATION
Without CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Stop engine.
3. Disconnect vacuum hose connected to EVAP service port and EVAP canister purge volume control sole-
noid valve from EVAP canister purge volume control solenoid valve.
4. Start engine and let it idle for at least 80 seconds.
5. Check vacuum hose for vacuum when revving engine up to 2,000 rpm.
OK or NG
OK
>> GO TO 15.
NG
>> GO TO 14.
14.
CHECK VACUUM HOSE
Check vacuum hoses for clogging or disconnection. Refer to
.
OK or NG
OK
>> GO TO 15.
BBIA0558E
Vacuum should exist.
2010 Pathfinder
P0456 EVAP CONTROL SYSTEM
EC-285
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NG
>> Repair or reconnect the hose.
15.
CHECK EVAP CANISTER PURGE VOLUME CONTROL SOLENOID VALVE
EC-250, "Component Inspection"
OK or NG
OK
>> GO TO 16.
NG
>> Replace EVAP canister purge volume control solenoid valve.
16.
CHECK FUEL TANK TEMPERATURE SENSOR
EC-200, "Component Inspection"
OK or NG
OK
>> GO TO 17.
NG
>> Replace fuel level sensor unit.
17.
CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
EC-266, "Component Inspection"
OK or NG
OK
>> GO TO 18.
NG
>> Replace EVAP control system pressure sensor.
18.
CHECK EVAP PURGE LINE
Check EVAP purge line (pipe, rubber tube, fuel tank and EVAP canister) for cracks or improper connection.
.
OK or NG
OK
>> GO TO 19.
NG
>> Repair or reconnect the hose.
19.
CLEAN EVAP PURGE LINE
Clean EVAP purge line (pipe and rubber tube) using air blower.
>> GO TO 20.
20.
CHECK EVAP/ORVR LINE
Check EVAP/ORVR line between EVAP canister and fuel tank for clogging, kinks, looseness and improper
connection. For location, refer to
.
OK or NG
OK
>> GO TO 21.
NG
>> Repair or replace hoses and tubes.
21.
CHECK RECIRCULATION LINE
Check recirculation line between filler neck tube and fuel tank for clogging, kinks, cracks, looseness and
improper connection.
OK or NG
OK
>> GO TO 22.
NG
>> Repair or replace hose, tube or filler neck tube.
22.
CHECK REFUELING EVAP VAPOR CUT VALVE
EC-415, "Component Inspection"
OK or NG
OK
>> GO TO 23.
NG
>> Replace refueling EVAP vapor cut valve with fuel tank.
23.
CHECK FUEL LEVEL SENSOR
MWI-33, "Component Inspection"
.
OK or NG
OK
>> GO TO 24.
NG
>> Replace fuel level sensor unit.
2010 Pathfinder
EC-286
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0456 EVAP CONTROL SYSTEM
24.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
>>
INSPECTION END
Component Inspection
INFOID:0000000005257263
FUEL TANK VACUUM RELIEF VALVE (BUILT INTO FUEL FILLER CAP)
1. Wipe clean valve housing.
2. Check valve opening pressure and vacuum.
3. If out of specification, replace fuel filler cap as an assembly.
CAUTION:
Use only a genuine fuel filler cap as a replacement. If an incor-
rect fuel filler cap is used, the MIL may come on.
SEF445Y
Pressure: 15.3 - 20.0 kPa (0.156 - 0.204 kg/cm
2
, 2.22 -
2.90 psi)
Vacuum:
−
6.0 to
−
3.3 kPa (
−
0.061 to
−
0.034 kg/cm
2
,
−
0.87 to
−
0.48 psi)
SEF943S
2010 Pathfinder
P0460 FUEL LEVEL SENSOR
EC-287
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0460 FUEL LEVEL SENSOR
Component Description
INFOID:0000000005257264
The fuel level sensor is mounted in the fuel level sensor unit. The
sensor detects a fuel level in the fuel tank and transmits a signal to
the combination meter. The combination meter sends the fuel level
sensor signal to the ECM through the CAN communication line.
It consists of two parts, one is mechanical float and the other is vari-
able resistor. Fuel level sensor output voltage changes depending on
the movement of the fuel mechanical float.
On Board Diagnosis Logic
INFOID:0000000005257265
NOTE:
•
If DTC P0460 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
•
If DTC P0460 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607.
Refer
.
When the vehicle is parked, the fuel level in the fuel tank is naturally stable. It means that output signal of the
fuel level sensor does not change. If ECM senses sloshing signal from the sensor, fuel level sensor malfunc-
tion is detected.
DTC Confirmation Procedure
INFOID:0000000005257266
1. If DTC Confirmation Procedure has been previously conducted, always perform the following before con-
ducting the next step.
a. Turn ignition switch OFF and wait at least 10 seconds.
b. Turn ignition switch ON.
c. Turn ignition switch OFF and wait at least 10 seconds.
2. Start engine and wait maximum of 2 consecutive minutes.
3. Check 1st trip DTC.
4. If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000005257267
1.
CHECK COMBINATION METER FUNCTION
.
OK or NG
OK
>> GO TO 2.
NG
>> Go to
MWI-32, "Component Function Check"
.
2.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
.
BBIA0529E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0460
0460
Fuel level sensor circuit
noise
Even though the vehicle is parked, a signal be-
ing varied is sent from the fuel level sensor to
ECM.
• Harness or connectors
(The CAN communication line is open or
shorted)
• Harness or connectors
(The sensor circuit is open or shorted)
• Combination meter
• Fuel level sensor
2010 Pathfinder
EC-288
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0460 FUEL LEVEL SENSOR
>>
INSPECTION END
2010 Pathfinder
P0461 FUEL LEVEL SENSOR
EC-289
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0461 FUEL LEVEL SENSOR
Component Description
INFOID:0000000005257268
The fuel level sensor is mounted in the fuel level sensor unit. The
sensor detects a fuel level in the fuel tank and transmits a signal to
the combination meter. The combination meter sends the fuel level
sensor signal to the ECM through CAN communication line.
It consists of two parts, one is mechanical float and the other is vari-
able resistor. Fuel level sensor output voltage changes depending on
the movement of the fuel mechanical float.
On Board Diagnosis Logic
INFOID:0000000005257269
NOTE:
•
If DTC P0461 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
•
If DTC P0461 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
.
Driving long distances naturally affect fuel gauge level.
This diagnosis detects the fuel gauge malfunction of the gauge not moving even after a long distance has
been driven.
Overall Function Check
INFOID:0000000005257270
Use this procedure to check the overall function of the fuel level sensor. During this check, a 1st trip DTC
might not be confirmed.
WARNING:
When performing the following procedure, always observe the handling of the fuel. Refer to
TESTING CONDITION:
Before starting overall function check, preparation of draining fuel and refilling fuel is required.
WITH CONSULT-III
NOTE:
Start from step 10, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/
8 Imp gal) in advance.
1. Prepare a fuel container and a spare hose.
2. Release fuel pressure from fuel line, refer to
.
3. Remove the fuel feed hose on the fuel level sensor unit.
4. Connect a spare fuel hose where the fuel feed hose was removed.
5. Turn ignition switch OFF and wait at least 10 seconds then turn ON.
6. Select “FUEL LEVEL SE” in “DATA MONITOR” mode with CONSULT-III.
7. Check “FUEL LEVEL SE” output voltage and note it.
8. Select “FUEL PUMP” in “ACTIVE TEST” mode with CONSULT-III.
9. Touch ON and drain fuel approximately 30 (7-7/8 US gal, 6-5/8 Imp gal) and stop it.
10. Check “FUEL LEVEL SE” output voltage and note it.
11. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
12. Check “FUEL LEVEL SE” output voltage and note it.
BBIA0529E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0461
0461
Fuel level sensor circuit
range/performance
The output signal of the fuel level sensor does
not change within the specified range even
though the vehicle has been driven a long dis-
tance.
• Harness or connectors
(The CAN communication line is open or
shorted)
• Harness or connectors
(The sensor circuit is open or shorted)
• Combination meter
• Fuel level sensor
2010 Pathfinder
EC-290
< COMPONENT DIAGNOSIS >
[VQ40DE]
P0461 FUEL LEVEL SENSOR
13. Confirm whether the voltage changes more than 0.03V during step 7 to 10 and 10 to 12.
If NG, go to
WITH GST
NOTE:
Start from step 8, if it is possible to confirm that the fuel cannot be drained by 30 (7-7/8 US gal, 6-5/8
Imp gal) in advance.
1. Prepare a fuel container and a spare hose.
2. Release fuel pressure from fuel line. Refer to
3. Remove the fuel feed hose on the fuel level sensor unit.
4. Connect a spare fuel hose where the fuel feed hose was removed.
5. Turn ignition switch ON.
6. Drain fuel by 30 (7-7/8 US gal, 6-5/8 Imp gal) from the fuel tank using proper equipment.
7. Confirm that the fuel gauge indication varies.
8. Fill fuel into the fuel tank for 30 (7-7/8 US gal, 6-5/8 Imp gal).
9. Confirm that the fuel gauge indication varies.
10. If NG, go to
Diagnosis Procedure
INFOID:0000000005257271
1.
CHECK COMBINATION METER FUNCTION
.
OK or NG
OK
>> GO TO 2.
NG
>> Go to
MWI-32, "Component Function Check"
.
2.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
>>
INSPECTION END
2010 Pathfinder
P0462, P0463 FUEL LEVEL SENSOR
EC-291
< COMPONENT DIAGNOSIS >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0462, P0463 FUEL LEVEL SENSOR
Component Description
INFOID:0000000005257272
The fuel level sensor is mounted in the fuel level sensor unit. The
sensor detects a fuel level in the fuel tank and transmits a signal to
the combination meter. The combination meter sends the fuel level
sensor signal to the ECM through CAN communication line.
It consists of two parts, one is mechanical float and the other is vari-
able resistor. Fuel level sensor output voltage changes depending on
the movement of the fuel mechanical float.
On Board Diagnosis Logic
INFOID:0000000005257273
NOTE:
•
If DTC P0462 or P0463 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC
UXXXX.
•
If DTC P0462 or P0463 is displayed with DTC P0607, first perform the trouble diagnosis for DTC
P0607. Refer to
DTC Confirmation Procedure
INFOID:0000000005257274
NOTE:
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next step.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11V at ignition
switch ON.
1. Turn ignition switch ON and wait at least 5 seconds.
2. Check 1st trip DTC.
3. If 1st trip DTC is detected, go to
Diagnosis Procedure
INFOID:0000000005257275
1.
CHECK COMBINATION METER FUNCTION
.
OK or NG
OK
>> GO TO 2.
NG
>> Go to
MWI-32, "Component Function Check"
.
2.
CHECK INTERMITTENT INCIDENT
GI-37, "Intermittent Incident"
.
BBIA0529E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0462
0462
Fuel level sensor circuit
low input
An excessively low voltage from the sensor is
sent to ECM.
• Harness or connectors
(The CAN communication line is open or
shorted)
• Harness or connectors
(The sensor circuit is open or shorted)
• Combination meter
• Fuel level sensor
P0463
0463
Fuel level sensor circuit
high input
An excessively high voltage from the sensor is
sent to ECM.
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст