Nissan Pathfinder (2010 year). Instruction — part 410
EXL-146
< ON-VEHICLE REPAIR >
ADJUSTMENT AND INSPECTION
Aiming Chart
NOTE:
• By regulation, no means for horizontal aim adjustment is provided from the factory; only vertical aim is
adjustable.
• Basic illuminating area for evaluation and/or adjustment should be within range shown on aiming chart.
1. Use adjustment screw to perform aiming adjustment.
•
Cover the opposite lamp and ensure fog lamps, if equipped, are turned off.
CAUTION:
Do not tighten adjustment screw beyond specified torque or damage may occur.
2. Adjust beam pattern until cut-off line (top edge of illumination area) is positioned at the specified height off
ground. Measure cut-off line within distance J on H-line. See aiming chart.
FRONT FOG LAMP
FRONT FOG LAMP : Aiming Adjustment
INFOID:0000000005259792
The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb. Before performing aiming
adjustment, make sure of the following.
• Keep all tires inflated to correct pressure.
WKIA4885E
1
Adjustment screen
2
Headlamp bulb center (HV point)
A
Minimum acceptable vertical aim di-
mension (see aiming chart)
B
Maximum acceptable vertical aim
dimension (see aiming chart)
C
H-V point
D
Distance of headlamp aiming screen
from vehicle 7.62 m (25 ft.)
E
Maximum aim evaluation distance
from vertical center on aiming
screen 399mm (3
°
R).
F
Minimum aim evaluation distance
from vertical center on aiming
screen 133 mm (1
°
R)
G
Aim evaluation area
H
Horizontal aiming evaluation line.
⇒
Right
A (Minimum acceptable vertical aim dimension)
-3.3 mm (0.13 in)
0.025
°
up
B (Maximum acceptable vertical aim dimension) 36.6 mm (1.44 in)
0.275
°
down
Adjustment torque
1.67 N.m (17 kg-cm, 14.8 in-lb)
2010 Pathfinder
ADJUSTMENT AND INSPECTION
EXL-147
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• Place vehicle on level ground.
• See that vehicle is unloaded (except for full levels of coolant, engine oil and fuel, and spare tire, jack, and
tools). Have the driver or equivalent weight placed in driver seat.
Adjust aiming in the vertical direction by turning the adjustment
screw.
NOTE:
Use a Phillips screwdriver to adjust. Turn screw clockwise to raise
pattern and counterclockwise to lower pattern.
1. Set the distance between the screen and the center of the fog
lamp lens as shown.
2. Turn front fog lamps ON.
3. Remove front portion of fender protector(s) for adjustment screw access. Refer to
Installation of Front Fender Protector"
4. Adjust front fog lamps using adjustment screw so that the top
edge of the high intensity zone is 100 mm (4 in) below the height
of the fog lamp centers as shown.
• When performing adjustment, if necessary, cover the headlamps
and opposite fog lamp.
LKIA0572E
MEL327G
MEL328G
2010 Pathfinder
EXL-148
< REMOVAL AND INSTALLATION >
HEADLAMP
REMOVAL AND INSTALLATION
HEADLAMP
Bulb Replacement
INFOID:0000000005259793
HEADLAMP BULB
Removal
NOTE:
Reach through engine room for bulb replacement access.
CAUTION:
Grasp only the plastic base when handling the bulb. Never touch the glass envelope.
1. Turn front headlamp switch OFF.
2. Disconnect the electrical connector.
3. Rotate the headlamp bulb retaining ring counterclockwise and remove.
4. Pull the headlamp bulb straight out from the headlamp assembly.
NOTE:
Remove the headlamp bulb from the headlamp assembly just before a replacement bulb is installed. Dust,
moisture, foreign materials, etc. entering headlamp body may affect performance.
Installation
Installation is in the reverse order of removal.
FRONT TURN SIGNAL/PARKING LAMP
Removal
NOTE:
Reach through engine room for bulb replacement access.
1. Turn the bulb socket counterclockwise to unlock it.
2. Pull the bulb to remove it from the socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, be sure to install the bulb socket securely for watertightness.
FRONT SIDE MARKER LAMP
Removal
NOTE:
Reach through engine room for bulb replacement access.
1. Turn the bulb socket counterclockwise to unlock it.
2. Pull the bulb to remove it from the socket.
Installation
Installation is in the reverse order of removal.
CAUTION:
After installing the bulb, be sure to install the bulb socket securely for watertightness.
Removal and Installation
INFOID:0000000005259794
FRONT COMBINATION LAMP
Removal
1. Remove front portion of front fender protector. Refer to
EXT-23, "Removal and Installation of Front Fender
.
2. Remove the front bumper. Refer to
EXT-14, "Removal and Installation"
.
3. Remove the front combination lamp bolts.
4. Disconnect the front combination lamp connector and remove front combination lamp.
2010 Pathfinder
HEADLAMP
EXL-149
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Installation
Installation is in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000005259795
FRONT COMBINATION LAMP
Front combination lamp bolts ·: 6.0 Nm (0.61 kg-m, 53 in-lb)
1. Headlamp assembly
2. Headlamp bulb
3. Headlamp bulb retaining ring
4. Wiring harness assembly
5. Front side marker lamp bulb
6. Front turn signal/parking lamp bulb
AWKIA1398GB
2010 Pathfinder
EXL-150
< REMOVAL AND INSTALLATION >
OPTICAL SENSOR
OPTICAL SENSOR
Removal and Installation
INFOID:0000000005259796
REMOVAL
1. Twist the optical sensor counter clockwise to remove it from the instrument panel.
2. Disconnect the electrical connector and remove the optical sensor.
INSTALLATION
Installation is in the reverse order of removal.
2010 Pathfinder
FRONT FOG LAMP
EXL-151
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Bulb Replacement
INFOID:0000000005259797
1. Remove front portion of fender protector. Refer to
EXT-23, "Removal and Installation of Front Fender Pro-
2. Disconnect fog lamp connector.
3. Turn the bulb counterclockwise to remove it.
CAUTION:
• Do not touch the glass of bulb directly by hand. Keep
grease and other oily substances away from it. Do not
touch bulb by hand while it is lit or right after being turned
off. Burning may result.
• Do not leave bulb out of fog lamp reflector for a long time
because dust, moisture smoke, etc. may affect the perfor-
mance of fog lamp. When replacing bulb, be sure to
replace it with new one.
Removal and Installation
INFOID:0000000005259798
FRONT FOG LAMP
The fog lamp is a semi-sealed beam type which uses a replaceable halogen bulb.
CAUTION:
• Do not leave fog lamp assembly without bulb for a long period of time. Dust, moisture, smoke, etc.
entering the fog lamp body may affect the performance. Remove the bulb from the headlamp assem-
bly just before replacement bulb is installed.
• Grasp only the plastic base when handling the bulb. Never touch the glass envelope. Touching the
glass could significantly affect the bulb life and/or fog lamp performance.
Removal
1. Remove front portion of fender protector. Refer to
EXT-23, "Removal and Installation of Front Fender Pro-
2. Disconnect fog lamp connector.
3. Remove fog lamp screws and pull fog lamp rearward out of front
bumper.
Installation
Installation is in the reverse order of removal.
LKIA0573E
LKIA0574E
2010 Pathfinder
EXL-152
< REMOVAL AND INSTALLATION >
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000005259799
REMOVAL
1. Disconnect battery negative and positive terminals.
2. Remove instrument lower cover LH. Refer to
3. Remove steering column cover.
4. Disconnect the lighting and turn signal switch connector.
5. While pressing tabs, pull lighting and turn signal switch toward
driver door and release from the steering column.
INSTALLATION
Installation is in the reverse order of removal.
LKIA0013E
2010 Pathfinder
HAZARD SWITCH
EXL-153
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Removal and Installation
INFOID:0000000005259800
REMOVAL
1. Remove cluster lid C. Refer to
.
2. Disconnect the hazard switch connector.
3. Remove the screws and remove the hazard switch.
INSTALLATION
Installation is in the reverse order of removal.
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст