Nissan Pathfinder (2010 year). Instruction — part 127
CO-14
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
ENGINE COOLANT
2. Set the vehicle heater controls to the full HOT and heater ON position. Turn the vehicle ignition ON with
the engine OFF as necessary to activate the heater mode.
3. Remove the vented reservoir cap and replace it with a non-vented reservoir cap before filling the cooling
system.
4. Install the Tool by installing the radiator cap adapter onto the
radiator neck opening. Then attach the gauge body assembly
with the refill tube and the venturi assembly to the radiator cap
adapter.
5. Insert the refill hose into the coolant mixture container that is
placed at floor level. Make sure the ball valve is in the closed
position.
• Use recommended coolant or equivalent.
Refer to
.
6. Install an air hose to the venturi assembly, the air pressure must
be within specification.
CAUTION:
The compressed air supply must be equipped with an air
dryer.
7. The vacuum gauge will begin to rise and there will be an audible hissing noise. During this process open
the ball valve on the refill hose slightly. Coolant will be visible rising in the refill hose. Once the refill hose is
full of coolant, close the ball valve. This will purge any air trapped in the refill hose.
8. Continue to draw the vacuum until the gauge reaches 28 inches
of vacuum. The gauge may not reach 28 inches in high altitude
locations, use the vacuum specifications based on the altitude
above sea level.
9. When the vacuum gauge has reached the specified amount, disconnect the air hose and wait 20 seconds
to see if the system loses any vacuum. If the vacuum level drops, perform any necessary repairs to the
system and repeat steps 6 - 8 to bring the vacuum to the specified amount. Recheck for any leaks.
10. Place the coolant container (with the refill hose inserted) at the same level as the top of the radiator. Then
open the ball valve on the refill hose so the coolant will be drawn up to fill the cooling system. The cooling
system is full when the vacuum gauge reads zero.
CAUTION:
Do not allow the coolant container to get too low when filling, to avoid air from being drawn into
the cooling system.
C
Yes
Refer to
EM-102, "Disassembly and Assembly"
D
Plug
Yes
Refer to
EM-102, "Disassembly and Assembly"
Block heater
Refer to
EM-102, "Disassembly and Assembly"
Part
Washer
Tightening Torque
Tool number
: KV991J0070 (J-45695)
Cooling system capacity
(with reservoir)
: Refer to
Compressed air
supply pressure
: 549 - 824 kPa (5.6 - 8.4 kg/cm
2
,
80 - 119 psi)
LLIA0058E
Altitude above sea level
Vacuum gauge reading
0 - 100 m (328 ft)
: 28 inches of vacuum
300 m (984 ft)
: 27 inches of vacuum
500 m (1,641 ft)
: 26 inches of vacuum
1,000 m (3,281 ft)
: 24 - 25 inches of vacuum
LLIA0057E
2010 Pathfinder
ENGINE COOLANT
CO-15
< ON-VEHICLE MAINTENANCE >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
11. Remove the Tool from the radiator neck opening and install the radiator cap.
12. Remove the non-vented reservoir cap.
13. Fill the cooling system reservoir tank to the specified level. Run the engine to warm up the cooling system
and top up the system as necessary before installing the vented reservoir cap.
FLUSHING COOLING SYSTEM
1. Drain the water from the engine cooling system. Refer to
CO-12, "Changing Engine Coolant"
.
2. Fill the radiator and the reservoir tank (to the “MAX” line), with water. Reinstall the radiator cap and leave
the vented reservoir cap off.
3. Run the engine until it reaches normal operating temperature.
4. Press the engine accelerator two or three times under no-load.
5. Stop the engine and wait until it cools down.
6. Drain the water from the engine cooling system. Refer to
CO-12, "Changing Engine Coolant"
.
7. Repeat steps 2 through 6 until clear water begins to drain from the radiator.
2010 Pathfinder
CO-16
< ON-VEHICLE REPAIR >
[VQ40DE]
RADIATOR
ON-VEHICLE REPAIR
RADIATOR
Exploded View
INFOID:0000000005260558
Removal and Installation
INFOID:0000000005260559
WARNING:
Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine
coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to
release built-up pressure. Carefully remove radiator cap by turning it all the way.
REMOVAL
1. Remove engine under cover. Refer to
EXT-14, "Removal and Installation"
2. Drain engine coolant from radiator. Refer to
CAUTION:
• Perform this step when engine is cold.
• Do not spill engine coolant on drive belts.
1.
Upper mount bracket
2.
Mounting rubber (upper)
3.
Radiator cap
4.
Radiator
5.
Mounting rubber (lower)
6.
A/T fluid cooler hose
7.
A/T fluid cooler hose
8.
O-ring
9.
Drain plug
10. Cooling fan assembly
11. Radiator shroud (upper)
12. Radiator hose (lower)
13. Radiator shroud (lower)
14. Reservoir tank hose
15. Reservoir tank cap
16. Reservoir tank
17. Water hose
18. Radiator hose (upper)
A.
To heater return tube
B.
To water pipe
C.
To A/T cooler tube
D.
To water inlet and thermostat assembly
Vehicle front
PBIC3861E
2010 Pathfinder
RADIATOR
CO-17
< ON-VEHICLE REPAIR >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
3. Remove engine room cover. Refer to
EM-25, "Removal and Installation"
4. Remove air duct and resonator assembly and air cleaner case (upper). Refer to
.
5. Remove reservoir tank hose.
6. Remove radiator hoses (upper and lower).
CAUTION:
Be careful not to allow engine coolant to contact drive belts.
7. Disconnect A/T fluid cooler hoses.
• Install blind plug to avoid leakage of A/T fluid.
8. Remove radiator shroud (lower).
9. Remove radiator shroud (upper).
10. Remove engine cooling fan (Motor driven type). Refer to
CO-20, "Removal and Installation (Motor driven
.
11. Remove front grille. Refer to
EXT-18, "Removal and Installation"
12. Remove the upper mount bracket bolts.
13. Remove the two A/C condenser bolts.
14. Remove radiator as follows:
CAUTION:
Do not damage or scratch A/C condenser and radiator core when removing.
a. With lifting and pulling radiator in a rear direction, disassemble
mounting rubber (lower) from radiator core support center.
CAUTION:
Because A/C condenser is attached to the front-lower por-
tion of radiator, moving it in the rear direction should be at a
minimum.
LBIA0419E
LBIA0421E
PBIC1936E
2010 Pathfinder
CO-18
< ON-VEHICLE REPAIR >
[VQ40DE]
RADIATOR
b. Lift A/C condenser up and remove radiator after disengaging the
fitting at front-bottom surface.
CAUTION:
Lifting A/C condenser should be minimum to prevent a load
to A/C piping.
c.
After removing radiator, put A/C condenser on radiator core sup-
port center to prevent a load to A/C piping, and temporarily fix it
with rope or similar means.
INSTALLATION
Installation is in the reverse order of removal.
INSPECTION AFTER INSTALLATION
• Check for leaks of engine coolant. Refer to
.
• Start and warm up engine. Visually check there are no leaks of engine coolant and A/T fluid.
Checking Radiator
INFOID:0000000005260560
Check radiator for mud or clogging. If necessary, clean radiator as follows.
CAUTION:
• Be careful not to bend or damage the radiator fins.
• When radiator is cleaned without removal, remove all surrounding parts such as cooling fan, radia-
tor shroud and horns. Then tape the harness and electrical connectors to prevent water from enter-
ing.
1. Apply water by hose to the back side of the radiator core vertically downward.
2. Apply water again to all radiator core surfaces.
3. Stop washing when dirt and debris no longer flow out from the radiator.
4. Blow air into the back side of radiator core vertically downward.
• Use compressed air lower than 490 kPa (5 kg/cm
2
, 71 psi) and keep distance more than 30 cm (11.8 in).
5. Blow air again into all the radiator core surfaces until no water sprays out.
6. Check for leaks.
PBIC1054E
2010 Pathfinder
ENGINE COOLING FAN
CO-19
< ON-VEHICLE REPAIR >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
ENGINE COOLING FAN
Exploded View
INFOID:0000000005260561
Crankshaft Driven Type
Removal and Installation (Crankshaft driven type)
INFOID:0000000005260562
REMOVAL
1. Remove engine front undercover. Refer to
EXT-14, "Removal and Installation"
2. Partially drain engine coolant from radiator. Refer to
.
CAUTION:
• Perform this step when engine is cold.
• Do not spill engine coolant on drive belts.
3. Remove the engine room cover. Refer to
EM-25, "Removal and Installation"
4. Remove air duct and resonator assembly. Refer to
EM-26, "Removal and Installation"
5. Remove reservoir tank hose from radiator.
6. Removal radiator hose (upper) from radiator.
CAUTION:
Do not spill engine coolant on drive belts.
7. Release the radiator shroud (lower) (2) from the radiator shroud
(upper) (1) and position aside.
• Release the tabs, pull radiator shroud (lower) (2) rearwards
and down.
8. Remove the radiator shroud (upper) bolts and remove the radiator shroud (upper). Refer to
9. Remove the engine cooling fan (Motor driven type). Refer to
CO-20, "Removal and Installation (Motor
10. Remove the drive belt. Refer to
EM-14, "Removal and Installation"
.
11. Remove the engine cooling fan.
12. Remove the fan coupling, if necessary.
13. Remove the cooling fan pulley, if necessary.
14. Remove the drive belt auto-tensioner, if necessary.
15. Remove the fan bracket, if necessary.
WBIA0726E
1.
Cooling fan
2.
Fan coupling
3.
Fan bracket
4.
Cooling fan pulley
ALBIA0470ZZ
2010 Pathfinder
CO-20
< ON-VEHICLE REPAIR >
[VQ40DE]
ENGINE COOLING FAN
INSPECTION AFTER REMOVAL
Fan Coupling
• Inspect fan coupling for oil leakage and bimetal conditions.
• If there are any unusual concerns, replace the fan coupling.
Fan Bracket
• Visually check that there is no significant looseness in the fan
bracket shaft, and that it turns smoothly by hand.
• If there are any unusual concerns, replace the fan bracket assem-
bly.
INSTALLATION
Installation is in the reverse order of removal.
• Install cooling fan with its front mark “F” facing front of engine. Refer to
CO-19, "Removal and Installation
INSPECTION AFTER INSTALLATION
• Check for leaks of the engine coolant. Refer to
• Start and warm up the engine. Visually make sure that there are no leaks of the engine coolant.
Removal and Installation (Motor driven type)
INFOID:0000000005260563
REMOVAL
1. Remove the engine under cover. Refer to
EXT-14, "Removal and Installation"
.
2. Partially drain engine coolant from radiator. Refer to
CO-12, "Changing Engine Coolant"
.
CAUTION:
• Perform this step when engine is cold.
• Do not spill engine coolant on drive belts.
3. Release the radiator shroud (lower) (2) from the radiator shroud
(upper) (1) and position aside.
• Release the tabs, pull radiator shroud (lower) (2) rearwards
and down.
4. Remove engine room cover. Refer to
EM-25, "Removal and Installation"
5. Remove air duct and resonator assembly. Refer to
EM-26, "Removal and Installation"
SLC072
LBIA0422E
ALBIA0470ZZ
2010 Pathfinder
ENGINE COOLING FAN
CO-21
< ON-VEHICLE REPAIR >
[VQ40DE]
C
D
E
F
G
H
I
J
K
L
M
A
CO
N
P
O
6. Remove upper radiator hose from radiator.
7. Remove reservoir tank hose from radiator shroud (upper) and radiator.
8. Remove the radiator shroud (upper) bolts and remove the radiator shroud (upper). Refer to
9. Disconnect harness connector from fan motor.
10. Remove the bolt and remove the fan grille and motor assembly.
INSTALLATION
Installation is in the reverse order of removal.
• Cooling fan is controlled by ECM. For details, refer to
.
AWBIA0148ZZ
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст