Nissan Pathfinder (2010 year). Instruction — part 658
WT-4
< BASIC INSPECTION >
DIAGNOSIS AND REPAIR WORKFLOW
3.
SELF-DIAGNOSIS
Perform SELF-DIAGNOSIS. Refer to
WT-33, "Self-Diagnosis (With CONSULT-III)"
.
>> GO TO 4
4.
SYMPTOM
>> GO TO 5
5.
MALFUNCTIONING PARTS
Repair or replace the applicable parts.
>> GO TO 6
6.
DRIVE TEST
1. Perform a drive test.
2. Check the low tire pressure warning lamp.
>> GO TO 7
7.
SELF-DIAGNOSIS
Perform SELF-DIAGNOSIS. Refer to
WT-33, "Self-Diagnosis (With CONSULT-III)"
.
Are any DTC's displayed?
YES
>> GO TO 5
NO
>> Inspection End
2010 Pathfinder
INSPECTION AND ADJUSTMENT
WT-5
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
INSPECTION AND ADJUSTMENT
Preliminary Check
INFOID:0000000005255786
1.
TIRE PRESSURE
Check all tire pressures. Refer to
Do tire pressures match specification?
YES
>> GO TO 2.
NO
>> Adjust tire pressures to specified value.
2.
LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp activation.
Does the low tire pressure warning lamp activate for one second when ignition switch is turned ON?
YES
>> GO TO 3.
NO
WT-37, "Low Tire Pressure Warning Lamp Does Not Come On When Ignition Switch Is
.
3.
BCM CONNECTOR
1. Disconnect BCM harness connectors.
2. Check terminals for damage or loose connections.
3. Reconnect harness connectors.
Are BCM connectors damaged or loose?
YES
>> Repair or replace damaged parts.
NO
>> GO TO 4.
4.
TRANSMITTER ACTIVATION TOOL
Check battery in transmitter activation tool.
Is transmitter activation tool battery fully charged?
YES
>> Perform self-diagnosis. Refer to
WT-33, "Self-Diagnosis (With CONSULT-III)"
NO
>> Replace battery in transmitter activation tool.
Transmitter Wake Up Operation
INFOID:0000000005255787
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided asleep and must first be woken up using Transmitter Acti-
vation Tool J-45295 before ID registration can be performed.
1. Turn ignition switch ON. Push the transmitter activation tool
against the tire near the front left transmitter. Press the button for
5 seconds. The hazard warning lamps flash per the following
diagram.
2. Repeat this procedure for each tire in the following order: FL, FR, RR, RL.
Tool number
: (J-45295)
LEIA0036E
2010 Pathfinder
WT-6
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
3. When the BCM finishes assigning each tire ID, the BCM flashes the hazard warning lamps and sends
flashing indicator status by CAN according to the following time chart.
4. After completing wake up of all transmitters, make sure low tire pressure warning lamp goes out.
ID Registration Procedure
INFOID:0000000005255788
ID REGISTRATION WITH TRANSMITTER ACTIVATION TOOL
NOTE:
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided asleep and must first be woken up using Transmitter Acti-
vation Tool J-45295 before ID registration can be performed.
1. Connect CONSULT-III.
2. Select ID REGIST under BCM.
3. Push the transmitter activation tool against the tire near the front
left transmitter. Press the button for 5 seconds.
4. Register the IDs in order from FR LH, FR RH, RR RH and RR LH. When ID registration of each wheel has
been completed, the hazard warning lamps flash.
5. After completing all ID registrations, press END to complete the procedure.
NOTE:
Be sure to register all of the IDs in order from FR LH, FR RH, RR RH, to RR LH, or the self-diagnostic results
display will not function properly.
ID REGISTRATION WITHOUT TRANSMITTER ACTIVATION TOOL
NOTE:
WEIA0177E
Tool number
: (J-45295)
LEIA0036E
Step
Activation tire position
Hazard warning lamp
CONSULT-III
1
Front LH
2 times flashing
YET
↓
DONE
2
Front RH
3
Rear RH
4
Rear LH
2010 Pathfinder
INSPECTION AND ADJUSTMENT
WT-7
< BASIC INSPECTION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
This procedure must be done after replacement of a low tire pressure warning transmitter or BCM.
New replacement transmitters are provided asleep and must first be woken up using Transmitter Acti-
vation Tool J-45295 before ID registration can be performed.
1. Connect CONSULT-III.
2. Select ID REGIST under BCM.
3. Adjust the tire pressures to the values shown in the table and drive the vehicle at 40 km/h (25 MPH) or
more for a few minutes.
4. After completing all ID registrations, press END to complete the procedure.
5. Inflate all tires to proper pressure. Refer to
Tire position
Tire pressure kPa (kg/cm
2
, psi)
Front LH
250 (2.5, 36)
Front RH
230 (2.3, 33)
Rear RH
210 (2.1, 30)
Rear LH
190 (1.9, 27)
Activation tire position
CONSULT-III
Front LH
YET
↓
DONE
Front RH
Rear RH
Rear LH
2010 Pathfinder
WT-8
< FUNCTION DIAGNOSIS >
TPMS
FUNCTION DIAGNOSIS
TPMS
System Diagram
INFOID:0000000005255789
System Description
INFOID:0000000005255790
BODY CONTROL MODULE (BCM)
The BCM (1) is shown with the lower instrument panel LH removed.
The BCM reads the air pressure signal received by the remote key-
less entry receiver, and controls the low tire pressure warning lamp
as shown below. It also has a self-diagnosis function to detect a sys-
tem malfunction.
TRANSMITTER
A sensor-transmitter integrated with a valve is installed in each
wheel, and transmits a detected air pressure signal in the form of a
radio wave. The radio signal is received by the remote keyless entry
receiver.
REMOTE KEYLESS ENTRY RECEIVER
ALEIA0004GB
Condition
Low tire pressure warning lamp
System normal
On for 1 second after ignition ON
Tire less than 193 kPa (2.0 kg/cm
2
, 28 psi)
[Flat tire]
ON
Low tire pressure warning system malfunc-
tion
After key ON, flashes once per sec-
ond for 1 minute, then stays ON
AWEIA0010ZZ
WEIA0137E
2010 Pathfinder
TPMS
WT-9
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
The remote keyless entry receiver is shown with the instrument
panel RH removed. The remote keyless entry receiver receives the
air pressure signal transmitted by the transmitter in each wheel.
COMBINATION METER
The combination meter receives tire pressure status from the BCM
using CAN communication. When a low tire pressure condition is
sensed by the BCM, the combination meter low tire pressure warn-
ing lamp is activated.
TIRE PRESSURE WARNING CHECK CONNECTOR
The tire pressure warning check connector can be grounded in order
to initiate self-diagnosis without a CONSULT-III. Refer to
"Self-Diagnosis (Without CONSULT-III)"
. The tire pressure warning
check connector (1) is located behind the lower portion of the instru-
ment panel LH.
DISPLAY UNIT (if equipped)
Displays the air pressure of each tire.
NOTE:
After the ignition switch is turned on, the pressure values will not be
displayed until the data of each wheel is received.
LEIA0069E
LEIA0055E
AWEIA0120ZZ
AWEIA0002GB
2010 Pathfinder
WT-10
< FUNCTION DIAGNOSIS >
TPMS
System Component
INFOID:0000000005255791
AWEIA0011ZZ
1.
AV control unit M37, M48 (with BOSE
audio system - with NAVI)
AV control unit M45, M70 (with BOSE
audio system - without NAVI)
AV control unit M133, M135 (with mid
audio system)
2.
Tire pressure warning check connec-
tor M123
3.
Transmitter
4.
BCM M18, M20
5.
Transmitter
6.
Combination meter M24
7.
Display unit M92 (with BOSE audio
system - with NAVI)
Display unit M93 (with mid audio sys-
tem or with BOSE audio system - with-
out NAVI)
8.
Remote keyless entry receiver M120
2010 Pathfinder
DIAGNOSIS SYSTEM (BCM)
WT-11
< FUNCTION DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
DIAGNOSIS SYSTEM (BCM)
CONSULT-III Function (BCM)
INFOID:0000000005255792
CONSULT-III DIAGNOSTIC MODES
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
DESCRIPTION
During driving, the tire pressure monitoring system receives the signal transmitted from the transmitter
installed in each wheel, and turns on the low tire pressure warning lamp when the tire pressure becomes low.
The control unit (BCM) for this system has pressure judgement and self-diagnosis functions.
FUNCTION
When the tire pressure monitoring system detects low inflation pressure or an internal malfunction, the low tire
pressure warning lamp in the combination meter comes on. The malfunction is indicated by the low tire pres-
sure warning lamp flashing.
CONSULT-III Application to Tire Pressure Monitoring System
×
: Applicable
– : Not applicable
Data Monitor Mode
Diagnostic mode
Description
Work Support
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are re-
ceived from the BCM and received data is displayed.
Data Monitor
Displays BCM input/output data in real time.
Active Test
Operation of electrical loads can be checked by sending drive signal to them.
Self Diagnostic Result
Displays BCM self-diagnosis results.
CAN Diag Support Monitor
The result of transmit/receive diagnosis of CAN communication can be read.
ECU Identification
BCM part number can be read.
Configuration
Performs BCM configuration read/write functions.
ITEM
SELF DIAGNOSTIC RESULT
DATA MONITOR
Front - Left transmitter
×
×
Front - Right transmitter
×
×
Rear - Left transmitter
×
×
Rear - Right transmitter
×
×
Warning lamp
—
×
Buzzer
—
×
Vehicle speed
×
×
CAN Communication
×
×
MONITOR
CONDITION
SPECIFICATION
VEHICLE SPEED
Drive vehicle.
Vehicle speed (km/h or MPH)
AIR PRESS FL
• Drive vehicle for a few minutes.
or
• Ignition switch ON and activation tool
is transmitting activation signals.
Tire pressure (kPa or psi)
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст