Nissan Pathfinder (2010 year). Instruction — part 605
ST-30
< DISASSEMBLY AND ASSEMBLY >
POWER STEERING OIL PUMP
POWER STEERING OIL PUMP
Disassembly and Assembly
INFOID:0000000005260177
VQ40DE ENGINE
VK56DE ENGINE
AWGIA0122GB
1.
Connector
2.
Suction pipe
3.
O-ring
4.
Bracket
5.
Pulley
6.
Lock washer
7.
Body assembly
8.
Copper washers
Apply Genuine NISSAN PSF or equivalent
LGIA0038E
1.
Bracket
2.
Spring washer
3.
Pulley
4.
Power steering pump
5.
High pressure bracket
6.
O-ring
7.
Suction pipe
Front
Apply Genuine NISSAN PSF or equivalent
2010 Pathfinder
POWER STEERING OIL PUMP
ST-31
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
INSPECTION BEFORE DISASSEMBLY
Disassemble the power steering oil pump only if the following items are found.
• Deformed or damaged pulley, bracket, connector or suction pipe
• Oil leakage from the suction pipe or connector.
DISASSEMBLY
NOTE:
Mount the power steering oil pump in a vise as needed.
1. Remove the connector bolt, connector and copper washers.
CAUTION:
Do not reuse the copper washers.
2. Remove the suction pipe and O-ring.
CAUTION:
Do not reuse the O-ring.
3. Remove the pulley nut and pulley.
4. Remove the bracket bolts and bracket(s).
INSPECTION AFTER DISASSEMBLY
Body Assembly Inspection
Check the power steering oil pump body assembly for damage. If any damage is found, replace with a new
power steering oil pump assembly.
ASSEMBLY
Assembly is in the reverse order of disassembly.
CAUTION:
• Do not reuse the copper gaskets
• Do not reuse the O-ring. Apply a coat of Genuine NISSAN PSF or equivalent to the O-ring. Refer to
2010 Pathfinder
ST-32
< DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
STEERING GEAR AND LINKAGE
Disassembly and Assembly
INFOID:0000000005260178
CAUTION:
• Secure the gear housing assembly with a vise. Use copper plates or equivalent to prevent it from
being damaged. Do not grip the cylinder with a vise.
• Before performing disassembly, clean the gear housing assembly. Be careful not to allow any
cleaner to contact the discharge and return port connectors.
DISASSEMBLY
1. Remove the cylinder tubes from the gear housing assembly.
2. Loosen the lock nuts of the outer sockets, then remove the outer sockets from the inner sockets.
3. Remove the boot clamps from the boots, then remove the boots from the inner sockets and gear housing
assembly.
CAUTION:
• Do not reuse the large-diameter boot clamps.
• Do not damage the boots, inner socket or gear housing assembly. If they are damaged, replace
them.
4. Remove the inner sockets.
INSPECTION AFTER DISASSEMBLY
Boot
Check boot for tears, cracks and deformation. Replace if necessary.
1.
Boot clamp
2.
Inner socket
3.
Boot
4.
Boot clamp
5.
Outer socket
6.
Cylinder tubes
7.
Gear housing assembly
8.
Connector
AWGIA0123GB
2010 Pathfinder
STEERING GEAR AND LINKAGE
ST-33
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
Gear Housing Assembly
Check gear housing assembly for dents, cracks or damage. Replace as an assembly if necessary.
Outer Socket and Inner Socket
SWING TORQUE
• Measure the swing torque, using Tool. When ball stud and inner
socket start moving the measured value must be within the specifi-
cation. If the reading is outside the specification, replace the
socket.
ROTATING TORQUE
• Measure the rotating torque, using Tool. If the value is outside the
specification, replace the outer sockets.
AXIAL END PLAY
• Apply a load of 490 N (50 kg-f, 110 lb-f) to the ball stud axially. Use
a dial gauge to measure the amount of the movement that the stud
makes. If the value is outside the specification, replace the sock-
ets.
ASSEMBLY
1. Install the inner sockets.
Tool number
:
—
(J-44372)
WGIA0131E
Item
Outer socket
Inner socket
Measuring point
Cotter pin hole of stud
Refer to
ST-35, "Steering Outer Socket and Inner
Swing torque
Refer to
ST-35, "Steering Outer Socket and Inner Socket"
Refer to
ST-35, "Steering Outer Socket and Inner
Measuring value
Refer to
ST-35, "Steering Outer Socket and Inner Socket"
Refer to
ST-35, "Steering Outer Socket and Inner
Tool number
: ST3127S000 (J-25765-A)
Outer socket
rotating torque
Refer to
WGIA0132E
Outer socket Refer to
Inner socket
Refer to
SGIA0057E
2010 Pathfinder
ST-34
< DISASSEMBLY AND ASSEMBLY >
STEERING GEAR AND LINKAGE
2. Install the large-diameter side of the boots to the gear housing
assembly.
3. Install the small-diameter side of the boots to the groove of the
inner sockets.
4. Install the boot clamps to the boots, as shown.
CAUTION:
Do not reuse the large boot clamps.
5. Crimp the large boot clamps, using Tool.
6. Install the cylinder tubes to the gear housing assembly.
7. Install the lock nuts and outer sockets to the inner sockets.
8. Thread the outer sockets onto the inner sockets to the specified
length (L) and a minimum thread depth of 18 mm threads. Then
tighten the lock nuts to the specified torque. Refer to "Disassem-
bly and Assembly". Reconfirm that the tie-rod length (L) is within
specification.
SGIA0550E
AST139
Tool number : KV40107300 ( — )
RAC1133D
Maximum inner socket
length (L)
SGIA0167E
2010 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
ST-35
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Steering Wheel
INFOID:0000000005260179
Steering Column
INFOID:0000000005260180
Steering Outer Socket and Inner Socket
INFOID:0000000005260181
End play of the axle direction for steering wheel
0 mm (0 in)
Steering wheel turning force
39 N (4 kg-f, 9 lb-f) or less
Steering wheel play on the outer circumference
0
−
35 mm (0
−
1.38 in)
Steering column length
553.0 mm (21.77 in)
Tilt range (A)
73.5 mm (2.894 in)
WGIA0083E
Steering gear type
PR26AM
Outer socket
Swinging torque
0.3
−
2.9 N·m (0.03
−
0.29 kg-m, 3
−
25 in-lb)
Measurement on spring balance
• Measuring point: cotter pin hole of stud
4.84
−
46.7 N (0.50
−
4.7 kg-f, 4
−
34 lb-f)
Rotating torque
0.3
−
2.9 N·m (0.03
−
0.29 kg-m, 3
−
25 in-lb)
Axial end play
0.5 mm (0.020 in) or less
Inner socket
Swinging torque
1.0
−
7.8 N·m (0.11
−
0.79 kg-m, 9
−
69 in-lb)
Measurement on spring balance
• Measuring point: L mark see above,
L=84.0 mm (3.307 in) max.
12.1
−
93.7 N (1.3
−
9.5 kg-f, 9
−
69 lb-f)
Axial end play
0.2 mm (0.08 in) or less
SGIA0358E
2010 Pathfinder
ST-36
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Oil Pump
INFOID:0000000005260182
Steering Fluid
INFOID:0000000005260183
Maximum inner socket length (L)
84.0 mm (3.31 in) max
SGIA0167E
Oil pump relief hydraulic pressure
8.0
−
8.8 mPa (81.60
−
89.76 kg/cm
2
, 1160.0
−
1276.0 psi)
Fluid capacity
Approx. 1.0 (2 1/8 US pt, 1 3/4 Imp pt)
2010 Pathfinder
STR-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
STR
A
STR
N
O
P
CONTENTS
STARTING SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Power Generation Variable Voltage
Control System . . . . . . . . . . . . . . ..
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
FUNCTION DIAGNOSIS . . . . . . . ...
STARTING SYSTEM . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ....
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . ....
COMPONENT DIAGNOSIS . . . . . . .
B TERMINAL CIRCUIT . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
S CONNECTOR CIRCUIT . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Diagnosis Procedure - VQ40DE . . . . . . . ..
Diagnosis Procedure - VK56DE . . . . . . . ..
STARTING SYSTEM . . . . . . . . . . .
Wiring Diagram - VQ40DE . . . . . . . . . ..
Wiring Diagram - VK56DE . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . . ..
STARTING SYSTEM . . . . . . . . . . .
Symptom Table . . . . . . . . . . . . . ...
ON-VEHICLE REPAIR . . . . . . . . .
STARTER MOTOR . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
STARTER MOTOR . . . . . . . . . . ...
Starter . . . . . . . . . . . . . . . . . ..
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст