Nissan Pathfinder (2010 year). Instruction — part 226
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
DLN-381
< FUNCTION DIAGNOSIS >
[FRONT FINAL DRIVE: M205]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
FUNCTION DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005258487
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
"
"
"
"
"
"
"
"
Possible cause and SUSPECTED PARTS
G
e
ar t
oo
th
rou
gh
Gea
r co
nt
ac
t i
mp
rop
er
To
ot
h s
u
rf
ac
es
w
o
rn
In
co
rre
ct ba
ck
la
sh
Co
mp
an
io
n f
lan
ge
e
xc
es
si
ve
run
ou
t
Gea
r oi
l i
mp
rop
er
PR
OP
EL
LE
R
S
H
A
F
T
FRO
N
T A
X
L
E
F
R
ONT
SUSPENSI
ON
TI
RE
S
ROAD W
H
EEL
DRIV
E SHAFT
BR
AK
E
S
S
T
EERING
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
2010 Pathfinder
DLN-382
< ON-VEHICLE MAINTENANCE >
[FRONT FINAL DRIVE: M205]
DIFFERENTIAL GEAR OIL
ON-VEHICLE MAINTENANCE
DIFFERENTIAL GEAR OIL
Changing Differential Gear Oil
INFOID:0000000005258488
DRAINING
1. Stop the engine.
2. Remove the drain plug from the front final drive assembly to drain the differential gear oil.
3. Install the drain plug with sealant applied on the threads to the front final drive assembly. Tighten to the
specified torque. Refer to
DLN-390, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Prod-
FILLING
1. Remove the filler plug from the front final drive assembly.
2. Fill the front final drive assembly with new differential gear oil
until the level reaches the specified level near the filler plug hole.
3. Install the filler plug with sealant applied on the threads to the
front final drive assembly. Tighten to the specified torque. Refer
DLN-390, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Products and Sealants"
.
Checking Differential Gear Oil
INFOID:0000000005258489
DIFFERENTIAL GEAR OIL LEAKAGE AND LEVEL
1. Make sure that differential gear oil is not leaking from the front final drive assembly or around it.
2. Check the differential gear oil level from the filler plug hole as
shown.
CAUTION:
Do not start engine while checking differential gear oil level.
3. Install the filler plug with sealant applied on the threads to the
front final drive assembly. Tighten to the specified torque. Refer
DLN-390, "Disassembly and Assembly"
.
• Use High Performance Thread Sealant or equivalent. Refer to
GI-14, "Recommended Chemical Products and Sealants"
.
Differential gear oil
grade and capacity
LDIA0176E
LDIA0176E
2010 Pathfinder
SIDE OIL SEAL
DLN-383
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: M205]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ON-VEHICLE REPAIR
SIDE OIL SEAL
Removal and Installation
INFOID:0000000005258490
REMOVAL
1. Remove the front final drive assembly. Refer to
DLN-387, "Removal and Installation"
2. Remove the differential side shaft and differential side flange
using suitable tool.
3. Place a small hole in the side oil seal case using suitable tool.
4. Remove the side oil seal using Tool as shown.
INSTALLATION
1. Apply multi-purpose grease to the lips of the new side oil seal. Then drive the new side oil seal in evenly to
the gear carrier using suitable tool.
CAUTION:
• Do not reuse side oil seal.
• Do not incline the new side oil seal when installing.
• Apply multi-purpose grease to the lips of the new side oil seal.
2. Installation of the remaining components is in the reverse order of removal.
CAUTION:
Check the differential gear oil level after installation. Refer to
.
BDIA0006E
LDIA0129E
Tool number
: SP8P
LDIA0130E
2010 Pathfinder
DLN-384
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: M205]
FRONT OIL SEAL
FRONT OIL SEAL
Removal and Installation
INFOID:0000000005258491
REMOVAL
1. Remove the drive shafts from the front final drive assembly. Refer to
.
2. Remove the front propeller shaft from the front final drive assembly. Refer to
.
3. Measure the total preload torque. Refer to
DLN-390, "Disassembly and Assembly"
.
NOTE:
Record the total preload torque measurement.
4. Remove the drive pinion lock nut using suitable tool.
5. Put matching marks on the companion flange and drive pinion
using paint.
CAUTION:
Use paint to make the matching marks. Do not damage the
companion flange or drive pinion.
6. Remove companion flange using suitable tool.
7. Place a small hole in the front oil seal case using suitable tool.
BDIA0001E
LDIA0171E
LDIA0129E
2010 Pathfinder
FRONT OIL SEAL
DLN-385
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: M205]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
8. Remove the front oil seal using Tool as shown.
INSTALLATION
1. Apply multi-purpose grease to the lips of the new front oil seal.
Then drive the new front oil seal in evenly to the gear carrier
using Tool.
CAUTION:
• Do not reuse front oil seal.
• Do not incline the new front oil seal when installing.
• Apply multi-purpose grease to the lips of the new front oil
seal.
2. Install the companion flange to the drive pinion while aligning the matching marks.
3. Apply anti-corrosive oil to the threads of the drive pinion and the
seating surface of the new drive pinion lock nut. Then adjust the
drive pinion lock nut tightening torque using suitable tool A, and
check the total preload torque using Tool B.
• The total preload torque should be within the total preload
torque specification. When not replacing the collapsible
spacer, it should also be equal to the measurement taken dur-
ing removal plus an additional 0.56 N·m (0.06 Kg-m, 5 in-lb).
• If the total preload torque is low, tighten the drive pinion lock
nut in 6.8 N·m (0.69 Kg-m, 5ft-lb) increments until the total pre-
load torque is met.
CAUTION:
• Do not reuse drive pinion lock nut.
• Apply anti-corrosive oil to the threads of the drive pinion
and the seating surface of the new drive pinion lock nut.
• Adjust the drive pinion lock nut tightening torque to the
lower limit first. Do not exceed the drive pinion lock nut
.
• Do not loosen drive pinion lock nut to adjust the total preload torque. If the drive pinion lock nut
torque or the total preload torque exceeds the specifications, replace the collapsible spacer and
tighten it again to adjust. Refer to
DLN-390, "Disassembly and Assembly"
• After adjustment, rotate drive pinion back and forth 2 to 3 times to check for unusual noise, rota-
tion malfunction, and other malfunctions.
4. Installation of the remaining components is in the reverse order of removal.
CAUTION:
Check the differential gear oil level after installation. Refer to
.
Tool number
: SP8P
LDIA0130E
Tool number
: KV38100500 (J-25273)
BDIA0003E
Tool number
B: ST3127S000 (J-25765-A)
Total preload torque: Refer to
WDIA0381E
2010 Pathfinder
DLN-386
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: M205]
CARRIER COVER
CARRIER COVER
Removal and Installation
INFOID:0000000005258492
REMOVAL
1. Remove the front final drive assembly. Refer to
DLN-387, "Removal and Installation"
2. Remove the carrier cover bolts and separate the carrier cover
from the gear carrier using Tool.
CAUTION:
• Do not damage the mating surface.
• Do not insert flat-bladed screwdriver, this will damage the
mating surface.
INSTALLATION
1. Apply 3 mm (0.12 in) bead of sealant to the mating surface of
the carrier cover as shown.
• Use Genuine Silicone RTV or equivalent. Refer to
"Recommended Chemical Products and Sealants"
.
CAUTION:
Remove any old sealant adhering to the mating surfaces.
Also remove any moisture, oil, or foreign material adhering
to the application and mating surfaces.
2. Install the carrier cover to the gear carrier. Tighten the bolts to
the specified torque. Refer to
3. Install the front final drive assembly. Refer to
CAUTION:
Fill the front final drive assembly with recommended differential gear oil. Refer to
Tool number
: KV10111100 (J-37228)
PDIA0699E
SDIA3204E
2010 Pathfinder
FRONT FINAL DRIVE
DLN-387
< REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: M205]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
FRONT FINAL DRIVE
Removal and Installation
INFOID:0000000005258493
REMOVAL
1. Drain the differential gear oil. Refer to
2. Remove the drive shafts from the front final drive assembly. Refer to
.
3. Remove the front cross member.
4. Remove the front propeller shaft from the front final drive assembly. Refer to
.
5. Disconnect the vent hose from the front final drive assembly.
6. Support the front final drive assembly using a suitable jack.
1.
Front final drive assembly
2.
Front cross member
Front
AWDIA0019GB
2010 Pathfinder
DLN-388
< REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: M205]
FRONT FINAL DRIVE
7. Remove the front final drive assembly bolts, then remove the
front final drive assembly.
CAUTION:
Support the front final drive assembly while removing using
a suitable jack.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Make sure there are no pinched or restricted areas on the breather hose caused by folding or bend-
ing when installing it.
• Fill the front final drive assembly with differential gear oil after installation. Refer to
BDIA0008E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст