Nissan Pathfinder (2010 year). Instruction — part 562
FRONT SEAT
SE-37
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Fold Flat Passenger Seat
10. Leg cover
11. Seat cushion front finisher
12. Passenger seat wiring harness
13. Power seat frame assembly
14. Seat cushion inner finisher
15. Seat belt buckle assembly
16. Leg cover
17. Seat cushion rear finisher
18. Instruction seat frame assembly
19. Recline lever
20. Seat cushion rear finisher
21. Seatback board
22. Headrest holder with multi position
lock
23. Headrest holder
24. Seatback pad without side air bag
25. Seatback frame without side air bag
26. Damper assembly
27. Seatback heating element
LIIA2409E
2010 Pathfinder
SE-38
< DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
Seatback Assembly
INFOID:0000000005256415
REMOVAL
NOTE:
On vehicles equipped with side air bags, only complete seatback assemblies can be replaced.
1. Remove the seat assembly. Refer to
SE-30, "Removal and Installation"
.
2. Unzip the seatback trim flap (1).
3. Unclip the lower retainer (2).
4. For the passenger seatback, remove the seatback board from the seatback. Refer to
.
5. Unclip the seatback trim j-clips.
1.
Front seatback lever
2.
Seatback trim without side air bag
3.
Headrest
4.
Seatback assembly with side air bag 5.
Seat cushion assembly
6.
Seat cushion outer finisher
7.
Leg cover
8.
Seat frame assembly
9.
Passenger seat wiring harness
10. Seat cushion inner cover
11. Leg cover
12. Seat belt buckle assembly
13. Inboard reclining arm outer cover
14. Inboard reclining arm inner cover
15. Outboard reclining arm inner cover
16. Outboard reclining arm outer cover
17. Seat cushion rear finisher
18. Seatback board
19. Headrest holder with multi position
lock
20. Headrest holder
21. Seatback pad without side air bag
22. Seatback frame without side air bag
23. Seatback fold flat release lever as-
sembly
24. Damper assembly
LIIA2419E
SIIA0113E
2010 Pathfinder
FRONT SEAT
SE-39
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
6. Remove the bolts (2 for each side) and the seatback assembly.
DISASSEMBLY
NOTE:
On vehicles equipped with side air bags, only complete seatback assemblies can be replaced.
1. Remove the seatback assembly.
2. Remove the headrest.
3. From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
4. Remove the snap ring and the lumbar support lever knob.
5. Remove the seatback trim and pad assembly.
6. Remove the hog ring to separate the seatback trim from the pad and the heating element (if equipped).
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
Passenger Seatback Board
INFOID:0000000005547999
SOFT SEATBACK
Removal
LIIA2420E
LRS023
PIIA1156E
2010 Pathfinder
SE-40
< DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
1. The seatback board is attached to the seat frame with the follow-
ing:
• 2 top tabs (A)
• 2 side tabs (B)
• 2 bottom clips (C) (must be replaced)
2. Move seat to forward position.
3. Hold the seatback board as shown and pull the top of the seat-
back board away from the seat back frame.
4. Pull the middle part of the seatback board to disengage the side
tabs (A) from the seatback frame.
5. Pull the lower part of the seatback board to disengage the bot-
tom clips from the seatback frame.
Installation
Installation is in the reverse order of removal.
HARD SEATBACK
Removal
1. The seatback board is attached to the seat frame with the follow-
ing:
• 2 top tabs (A)
• 2 side tabs (B)
• 2 bottom clips (C) (must be replaced)
2. Move seat to forward position.
ALIIA0366ZZ
ALIIA0368ZZ
ALIIA0367ZZ
ALIIA0369ZZ
2010 Pathfinder
FRONT SEAT
SE-41
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
3. Hold the seatback board as shown and pull the bottom of the
seatback board away from the seat back frame.
4. Pull the middle part of the seatback board to disengage the side
tabs (A) from the seatback frame.
5. Lift the upper part of the seatback board to disengage the top
tabs from the seatback frame.
Installation
Installation is in the reverse order of removal.
Seat Cushion Trim and Pad
INFOID:0000000005256416
REMOVAL
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
• Always replace passenger seat cushion as an assembly.
• When removed, the passenger seat cushion must always be placed pan side UP to prevent damage.
• During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do
not add additional clips.
• The Occupant Classification System control module can only be replaced as part of the seat cushion
assembly.
1. Remove the front seat assembly. Refer to
SE-30, "Removal and Installation"
.
2. Remove the power seat switch knobs and power seat switch
escutcheon (if equipped) (or lift knobs on instruction seats).
ALIIA0370ZZ
ALIIA0371ZZ
LIIA0681E
2010 Pathfinder
SE-42
< DISASSEMBLY AND ASSEMBLY >
FRONT SEAT
3. Remove the seat cushion outer finisher.
4. Remove the power seat switch screws.
5. Remove four bolts and the seat cushion assembly.
• On the fold flat passenger seat it is necessary to unclip the
rear flap j-clip from the seat pan.
6. Remove the retainer on the seat cushion frame, then remove the harness connector for the seat cushion
heater (if equipped).
DISASSEMBLY
CAUTION:
• Front passenger seat is equipped with an Occupant Classification System sensor and control mod-
ule. Do not disassemble front passenger seat cushion assembly or remove the trim as this will affect
the Occupant Classification System calibration.
1. Remove the seat cushion assembly.
2. On the drivers seat only, remove the hog rings to separate the trim cover from the pad and seat cushion
heater unit.
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
LIIA0285E
SIIA0503E
2010 Pathfinder
REAR SEAT
SE-43
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
REAR SEAT
Exploded View
INFOID:0000000005256417
Disassembly and Assembly
INFOID:0000000005256418
Second Row Outer
ALJIA0227GB
2010 Pathfinder
SE-44
< DISASSEMBLY AND ASSEMBLY >
REAR SEAT
1.
Headrest
2.
Seatback pad
3.
Seatback frame
4.
Seatback panel
5.
LH Headrest locking guide
6.
RH Headrest guide
7.
Flipper panel
8.
Seat actuator assembly
9.
Reclining device inner cover
10. Reclining device inner mid cover
11. Latch assembly
12. Seat cushion frame assembly
13. Lower rear seat cover
14. Lower rear seat cover inner
15. Cushion floor latch
16. Seat cushion support frame assem-
bly
17. Lower rear seat cover outer
18. Seat cushion pad
19. Inner inboard reclining device cover 20. Inner outboard reclining device cover 21. Reclining device lever
22. Reclining device outer mid cover
23. Reclining device outer cover
24. Seatback trim cover
25. Seat cushion trim cover
26. Seat cushion assembly
27. Seatback assembly
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст