Nissan Pathfinder (2010 year). Instruction — part 196
REAR OIL SEAL
DLN-141
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REAR OIL SEAL
Removal and Installation
INFOID:0000000005258350
REMOVAL
1. Partially drain the transfer fluid. Refer to
2. Remove the rear propeller shaft. Refer to
DLN-325, "Removal and Installation"
(2S1330),
3. Remove the dust cover from the rear case.
CAUTION:
Do not damage the rear case.
4. Remove the rear oil seal from the rear case using Tool.
CAUTION:
Do not damage the rear case.
INSTALLATION
1. Install the new rear oil seal until it is flush with the end face of the
rear case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Apply petroleum jelly to the circumference of the new dust cover.
Position the new dust cover as shown.
CAUTION:
• Do not reuse dust cover.
• Position the protursion at the position shown.
• 1: Dust cover
• 2: Rear case assembly
• A: Protrusions
WDIA0127E
Tool number
: ST33290001 (J-34286)
LDIA0139E
Tool number
: ST30720000 (J-25405)
LDIA0140E
AWDIA0550GB
2010 Pathfinder
DLN-142
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
REAR OIL SEAL
3. Install the new dust cover to the rear case using Tool.
CAUTION:
• Do not reuse dust cover.
• Apply petroleum jelly to dust cover.
4. Install the rear propeller shaft. Refer to
(2S1330),
DLN-336, "Removal and Installation"
(2S1350).
5. Refill the transfer with fluid and check for fluid leakage and fluid
.
Tool number
: KV40105310 ( — )
PDIA0116E
2010 Pathfinder
SIDE OIL SEAL
DLN-143
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SIDE OIL SEAL
Removal and Installation
INFOID:0000000005258351
REMOVAL
1. Remove the front propeller shaft. Refer to
DLN-315, "Removal and Installation"
.
2. Remove the companion flange. Refer to
DLN-283, "Disassembly and Assembly"
.
3. Remove the transfer control device from the transfer assembly. Refer to
DLN-277, "Removal and Installa-
4. Remove the side oil seal using suitable tool.
CAUTION:
Do not damage shift cross.
INSTALLATION
1. Install the new side oil seal until it is flush with the end face of
case using Tool.
CAUTION:
• Do not reuse oil seal.
• Apply petroleum jelly to oil seal.
2. Install the transfer control device to the transfer assembly. Refer
DLN-277, "Removal and Installation"
3. Install the companion flange. Refer to
.
4. Install the front propeller shaft. Refer to
DLN-315, "Removal and Installation"
SDIA2666E
Tool number
: ST22360002 (J-25679-01)
SDIA2665E
2010 Pathfinder
DLN-144
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
TRANSFER CONTROL DEVICE
TRANSFER CONTROL DEVICE
Removal and Installation
INFOID:0000000005258352
REMOVAL
CAUTION:
Change vehicle state to 2WD, and then remove and install transfer control device.
1. Remove front propeller shaft. Refer to
DLN-315, "Removal and Installation"
.
2. Disconnect transfer control device connector.
3. Remove transfer control lever.
4. Disconnect vacuum line.
5. Remove transfer control device.
INTSTALLATION
CAUTION:
Check 4WD shift indicator after installation. Refer to
DLN-129, "Precaution for Transfer Assembly and
Transfer Control Unit Replacement"
Installation is in the reverse order of removal.
1.
Shift lever
2.
Actuator
SDIA2654E
2010 Pathfinder
AIR BREATHER HOSE
DLN-145
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000005258353
VQ40DE
CAUTION:
• Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
• Install each air breather hose into the breather tube (metal
connector) until the hose end reaches the end of the curve
section. Set each air breather hose with paint mark facing
upward.
• Install actuator/transfer motor air breather hose and transfer
air breather hose on clip A with the paint mark facing upward.
SDIA3339E
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Clip E
7.
Actuator
8.
Air breather hose clamp
9.
Clip F
10. Transfer motor
11. Breather tube (transfer)
SDIA3340E
SDIA3342E
2010 Pathfinder
DLN-146
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
AIR BREATHER HOSE
• Install clip C on actuator/transfer motor air breather hose and
transfer air breather hose with the paint mark matched.
• Install actuator/transfer motor air breather hose and transfer
air breather hose on clip D and clip E with the paint mark fac-
ing upward.
• Install the actuator air breather hose into the actuator (case
connector) until the hose end reaches the base of the tube.
Set actuator air breather hose with paint mark facing leftward.
• Install clip F on transfer motor air (control device) breather
hose and transfer air breather hose with the paint mark
matched.
SDIA3343E
SDIA3344E
SDIA3226E
SDIA3345E
2010 Pathfinder
AIR BREATHER HOSE
DLN-147
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the
base of the tube. Set transfer air breather hose with paint
mark facing upwards.
• Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end of
the curved section. Set transfer motor air breather hose with
paint mark facing leftward.
REMOVAL AND INSTALLATION
VK56DE
CAUTION:
• Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
SDIA3196E
SDIA3194E
AWDIA0010ZZ
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Actuator
7.
Air breather hose clamp
8.
Clip E
9.
Transfer motor
10. Breather tube (transfer)
Vehicle front
2010 Pathfinder
DLN-148
< ON-VEHICLE REPAIR >
[TRANSFER: ATX14B]
AIR BREATHER HOSE
• Install each air breather hose into the breather tube (4). Set
each air breather hose with paint mark facing upward.
- A: Paint marks
- 1: A/T breather hose
- 2: Transfer air breather hose
- 3: Actuator/transfer motor air breather hose
• Install actuator/transfer motor air breather hose (1) and trans-
fer air breather hose (2) on clip (A) with the paint mark (B) fac-
ing upward.
: Front
• Install clip (A) on actuator/transfer motor air breather hose (1)
and transfer air breather hose (2) with the paint mark (B)
matched.
: Front
• Install actuator/transfer motor air breather hose (1) and trans-
fer air breather hose (2) on clip (C) and clip (B) with the paint
mark (A) and (D) facing upward.
: Front
ALDIA0110ZZ
ALDIA0111ZZ
AWDIA0011ZZ
AWDIA0012ZZ
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст