Nissan Pathfinder (2010 year). Instruction — part 637
TM-224
< DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
32. Disconnect output speed sensor connector (1).
CAUTION:
Do not damage connector.
33. Straighten terminal clip (
) to free output speed sensor har-
ness.
34. Remove bolts (A), (B) and (C) from control valve with TCM.
35. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the instruction valve notch and
instruction plate height. Remove it vertically.
36. Remove the A/T fluid temperature sensor 2 or plug as shown below.
a.
A/T fluid temperature sensor 2
JSDIA1319ZZ
JSDIA1320ZZ
: Front
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA8077E
SCIA5260E
2010 Pathfinder
DISASSEMBLY
TM-225
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
i.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
ii.
Remove bracket from A/T fluid temperature sensor 2.
b.
Plug
i.
Remove plug (1) with bracket (2) from control valve with TCM.
ii.
Remove bracket (1) from plug (2).
SCIA5253E
SCIA5264E
JSDIA1311ZZ
JSDIA1312ZZ
2010 Pathfinder
TM-226
< DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
iii. RemoveO-ring (1) from plug (2).
37. Remove O-ring from A/T assembly harness connector.
38. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
39. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
40. Disconnect TCM connector (1) and transmission range switch
connector (2).
CAUTION:
Do not damage connectors.
JSDIA1313ZZ
SCIA5155E
SCIA5447E
SCIA5448E
JSDIA1317ZZ
2010 Pathfinder
DISASSEMBLY
TM-227
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
41. Remove rear extension assembly (2WD models) or adapter case assembly (4WD models) according to
the following procedures.
a.
2WD models
i.
Remove bolts for rear extension assembly and transmission
case.
ii.
Tap rear extension assembly with soft hammer.
iii. Remove rear extension assembly (with needle bearing) from
transmission case.
b.
4WD models
SCIA6941E
SCIA5028E
SCIA5029E
2010 Pathfinder
TM-228
< DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
i.
Remove adapter case to transmission case bolts.
• Self-sealing bolts (2)
ii.
Remove brackets (1) (if equipped).
iii. Tap adapter case assembly using suitable tool.
iv. Remove adapter case assembly (with needle bearing) from
transmission case.
v.
Remove gasket from transmission case.
WCIA0563E
SCIA5201E
SCIA5186E
SCIA5231E
2010 Pathfinder
DISASSEMBLY
TM-229
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
42. Remove bearing race from output shaft.
43. Remove output shaft from transmission case by rotating left and
right.
44. Remove parking gear from output shaft.
45. Remove seal rings from output shaft.
46. Remove needle bearing from transmission case.
SCIA5245E
SCIA5030E
SCIA5247E
SCIA5209E
SCIA5031E
2010 Pathfinder
TM-230
< DISASSEMBLY AND ASSEMBLY >
DISASSEMBLY
47. Remove output speed sensor (1) from transmission case.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings or any foreign material to get on
the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.
48. Remove reverse brake snap ring using two flat-bladed screw-
drivers.
NOTE:
Press out snap ring from the transmission case oil pan side gap
using a flat-bladed screwdriver, and remove it using a another
screwdriver.
49. Remove reverse brake retaining plate from transmission case.
• Check facing for burns, cracks or damage. If necessary,
replace the plate.
50. Remove N-spring from transmission case.
51. Remove reverse brake drive plates, driven plates and dish plate
from transmission case.
•
Check facing for burns, cracks or damage. If necessary,
replace the plate.
52. Remove snap ring using suitable tool.
: Bolt
JSDIA1321ZZ
SCIA5032E
SCIA5214E
SCIA2322E
SCIA2323E
2010 Pathfinder
DISASSEMBLY
TM-231
< DISASSEMBLY AND ASSEMBLY >
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
53. Remove spring retainer and return spring from transmission
case.
54. Remove seal rings from drum support.
55. Remove needle bearing from drum support edge surface.
56. Remove reverse brake piston from transmission case using
compressed air. Refer to
.
CAUTION:
Care should be taken not to abruptly blow air. It makes the
piston incline, and as a result, it becomes hard to disas-
semble the pistons.
SCIA2324E
SCIA3333E
SCIA2796E
SCIA5047E
2010 Pathfinder
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст