Nissan Tiida C11. Instruction — part 1300
REPAIR FOR COMPONENT PARTS
TM-251
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Bolt length, number and location:
*
: Reamer bolt and nut.
a.
Install and tighten bolts (B) to the specified torque.
b.
Install solenoid valve assembly (1) on control valve assembly.
c.
Tighten bolts (A), (C) and (G) to the specified torque.
d.
Remove reamer bolts (F), and then set oil strainer (1) on control
valve assembly
e.
Install and tighten bolts (A), (D), reamer bolts (F) and nuts to the
specified torque.
f.
Tighten bolts (E) to the specified torque.
Bolt symbol
A
B
C
D
E
F
*
G
Bolt length “
” [mm (in)]
13.5
(0.531)
58.0
(2.283)
40.0
(1.575)
66.0
(2.598)
33.0
(1.299)
78.0
(3.071)
18.0
(0.709)
Number of bolts
6
3
6
11
2
2
1
Tightening torque
[N·m (kg-m, in-lb)]
7.84 (0.80, 69)
3.92
(0.40, 35)
7.84 (0.80, 69)
Bolts:
7.84 N·m (0.80 kg-m, 69 in-lb)
ATL0032D
Bolts:
7.84 N·m (0.80 kg-m, 69 in-lb)
SCIA7008E
Nuts and bolts:
7.84 N·m (0.80 kg-m, 69 in-lb)
SCIA7131E
Bolts:
3.92 N·m (0.40 kg-m, 35 in-lb)
ATL0035D
TM-252
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
Control Valve Upper Body
INFOID:0000000001730986
COMPONENTS
1.
Retainer plate
2.
Plug
3.
Cooler check valve spring
4.
Cooler check valve
5.
Control valve upper body
6.
Pilot valve
7.
Pilot valve spring
8.
Retainer plate
9.
1-2 accumulator retainer plate
SCIA2960J
REPAIR FOR COMPONENT PARTS
TM-253
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DISASSEMBLY
1.
Remove valves at retainer plates.
CAUTION:
Do not use a magnetic pick-up tool.
a.
Use suitable tool (A) to remove retainer plates (1).
b.
Remove retainer plates (1) while holding spring, plugs (2) or
sleeves using suitable tool (A).
CAUTION:
Remove plugs (2) slowly to prevent internal parts from
jumping out.
10. 1-2 accumulator piston spring
11.
1-2 accumulator piston
12. Plug
13. Retainer plate
14.
Retainer plate
15. Plug
16. 1st reducing valve
17.
1st reducing valve spring
18. Retainer plate
19. 3-2 timing valve spring
20.
3-2 timing valve
21. Retainer plate
22. Plug
23.
Overrun clutch reducing valve
24. Overrun clutch reducing valve spring
25. Retainer plate
26.
Torque converter relief valve spring 27. Torque converter relief valve
28. Retainer plate
29.
Sleeve
30. Plug
31. Torque converter clutch control valve
spring
32.
Torque converter clutch control
valve
33. Retainer plate
34. Plug
35.
1-2 accumulator valve spring
36. 1-2 accumulator valve
SCIA4979E
SCIA7136E
SCIA7137E
TM-254
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
c.
Place mating surface of valve body face down, and remove
internal parts.
CAUTION:
• If a valve is hard to remove, place valve body face down
and lightly tap it with a soft hammer.
• Do not drop or damage valves and sleeves.
INSPECTION
Valve Springs
• Check each valve spring for damage or deformation. Also measure
free length and outer diameter. Refer to
.
• Replace valve springs if deformed or fatigued.
Control Valves
Check sliding surfaces of valves, sleeves and plugs. Replace if necessary.
ASSEMBLY
CAUTION:
• Apply ATF to all components before installation.
• Lay control valve body down when installing valves. Do not
stand control valve body upright.
Lubricate control valve body and all valves with ATF. Install control
valves by sliding them carefully into their bores.
CAUTION:
• Install each control valve one by one.
• Install control valves after checking, because some of them
are similar.
• Do not scratch or damage valve body.
SAT137D
SAT138D
SAT139D
SAT140DA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст