Nissan Tiida C11. Instruction — part 1469
FRONT WIPER ARM
WW-71
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
4.
Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L1” and “L2” (LHD) or "L3" and
"L4" (RHD) immediately before temporarily tightening the wiper
arm nuts.
5.
Spray washer fluid. Turn on wiper switch to operate wiper motor
and then turn it off.
6.
Make sure that wiper blades stop are within specifications. Refer
to
7.
Tighten wiper arm nuts to specification.
8.
Attach wiper arm caps.
Adjustment
INFOID:0000000001366663
WIPER BLADE POSITION ADJUSTMENT
To adjust the wiper arm stop location, the wiper arm must be
removed and installed.
Clearance between the top edge of cowl top cover and the tip of the
front wiper blade as shown.
L1 (LHD)
: 37.5
±
7.5 mm (1.48
±
0.295 in)
L2 (LHD)
: 42.7
±
7.5 mm (1.68
±
0.295 in)
L3 (RHD)
: 38.0
±
7.5 mm (1.50
±
0.295 in)
L4 (RHD)
: 39.0
±
7.5 mm (1.54
±
0.295 in)
A
Cowl top cover top edge
AWLIA0020ZZ
L1 (LHD)
: 37.5
±
7.5 mm (1.48
±
0.295 in)
L2 (LHD)
: 42.7
±
7.5 mm (1.68
±
0.295 in)
L3 (RHD)
: 38.0
±
7.5 mm (1.50
±
0.295 in)
L4 (RHD)
: 39.0
±
7.5 mm (1.54
±
0.295 in)
A
Cowl top cover top edge
AWLIA0020ZZ
WW-72
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000001450763
LHD Models
LKIA0786E
1.
Front RH wiper blade
2.
Front RH wiper arm
3.
Wiper arm cap
4.
Front wiper drive assembly
5.
Front LH wiper arm
6.
Wiper arm cap
7.
Front LH wiper blade
FRONT WIPER DRIVE ASSEMBLY
WW-73
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
RHD Models
Removal and Installation
INFOID:0000000001450837
REMOVAL
1.
Operate the front wiper motor, and then turn off (auto stop).
2.
Remove wiper arms. Refer to
WW-70, "Removal and Installation"
.
3.
Remove cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
4.
Disconnect wiper motor connector.
5.
Remove front wiper drive assembly bolts, and remove front wiper drive assembly.
INSTALLATION
1.
Install front wiper drive assembly.
2.
Connect wiper motor connector. Turn wiper switch on to operate wiper motor, then turn wiper switch off
(auto stop).
3.
Install cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
4.
Install the wiper arms and adjust as necessary. Refer to
Adjustment
INFOID:0000000001450764
WIPER BLADE POSITION ADJUSTMENT
ALLIA0278ZZ
1.
Wiper arm cap
2.
Front RH wiper arm
3.
Wiper arm cap
4.
Front LH wiper arm
5.
Front wiper drive assembly
6.
Front LH wiper blade
7.
Front RH wiper blade
WW-74
< ON-VEHICLE REPAIR >
FRONT WIPER DRIVE ASSEMBLY
To adjust the wiper arm stop location, the wiper arm must be
removed and installed.
Clearance between the top edge of the cowl top cover and the tip of
the front wiper blade as shown.
L1 (LHD)
: 37.5
±
7.5 mm (1.48
±
0.295 in)
L2 (LHD)
: 42.7
±
7.5 mm (1.68
±
0.295 in)
L3 (RHD)
: 38.0
±
7.5 mm (1.50
±
0.295 in)
L4 (RHD)
: 39.0
±
7.5 mm (1.54
±
0.295 in)
A
Cowl top cover top edge
AWLIA0020ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст