Nissan Tiida C11. Instruction — part 434
EC-386
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
INSPECTION AND ADJUSTMENT
2.
Rev engine (2,000 to 3,000 rpm) two or three times under no
load, then run engine at idle speed for about 1 minute.
3.
Check idle speed.
For procedure, refer to
EC-389, "IDLE SPEED : Special Repair
.
For specification, refer to
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> GO TO 4.
4.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.
Stop engine.
2.
EC-389, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Require-
>> GO TO 5.
5.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-390, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
.
>> GO TO 6.
6.
PERFORM IDLE AIR VOLUME LEARNING
Perform
EC-390, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
Is Idle Air Volume Learning carried out successfully?
YES
>> GO TO 7.
NO
>> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
7.
CHECK TARGET IDLE SPEED AGAIN
1.
Start engine and warm it up to normal operating temperature.
2.
Check idle speed.
For procedure, refer to
EC-389, "IDLE SPEED : Special Repair Requirement"
For specification, refer to
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the Following.
• Check camshaft position sensor (PHASE) and circuit. Refer to
.
• Check crankshaft position sensor (POS) and circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace. Then GO TO 4.
9.
CHECK ECM FUNCTION
1.
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is a rare case.)
2.
Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to
RE-COMMUNICATING FUNCTION : Special Repair Requirement"
.
>> GO TO 4.
10.
CHECK IGNITION TIMING
1.
Run engine at idle.
PBIA8513J
INSPECTION AND ADJUSTMENT
EC-387
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
Check ignition timing with a timing light.
For procedure, refer to
EC-389, "IGNITION TIMING : Special
For specification, refer to
Is the inspection result normal?
YES
>> GO TO 19.
NO
>> GO TO 11.
11.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.
Stop engine.
2.
EC-389, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Require-
.
>> GO TO 12.
12.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-390, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
.
>> GO TO 13.
13.
PERFORM IDLE AIR VOLUME LEARNING
Perform
EC-390, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
Is Idle Air Volume Learning carried out successfully?
YES
>> GO TO 14.
NO
>> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
14.
CHECK TARGET IDLE SPEED AGAIN
1.
Start engine and warm it up to normal operating temperature.
2.
Check idle speed.
For procedure, refer to
EC-389, "IDLE SPEED : Special Repair Requirement"
.
For specification, refer to
Is the inspection result normal?
YES
>> GO TO 15.
NO
>> GO TO 17.
15.
CHECK IGNITION TIMING AGAIN
1.
Run engine at idle.
2.
Check ignition timing with a timing light.
For procedure, refer to
EC-389, "IGNITION TIMING : Special
For specification, refer to
Is the inspection result normal?
YES
>> GO TO 19.
NO
>> GO TO 16.
16.
CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Refer to
EM-50, "Removal and Installation"
Is the inspection result normal?
YES
>> GO TO 17.
NO
>> Repair the timing chain installation. Then GO TO 4.
1
: Timing indicator
MBIB1331E
1
: Timing indicator
MBIB1331E
EC-388
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
INSPECTION AND ADJUSTMENT
17.
DETECT MALFUNCTIONING PART
Check the following.
• Check camshaft position sensor (PHASE) and circuit. Refer to
.
• Check crankshaft position sensor (POS) and circuit. Refer to
.
Is the inspection result normal?
YES
>> GO TO 18.
NO
>> Repair or replace. Then GO TO 4.
18.
CHECK ECM FUNCTION
1.
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is a rare case.)
2.
Perform initialization of and registration of all NATS ignition key IDs. Refer to
NICATING FUNCTION : Special Repair Requirement"
.
>> GO TO 4.
19.
INSPECTION END
If ECM is replaced during this BASIC INSPECTION procedure, go to
WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
>> INSPECTION END
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000001161430
When replacing ECM, this procedure must be performed.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000001161431
1.
PERFORM INITIALIZATION OF NATS SYSTEM AND REGISTRATION OF ALL NATS IGNITION KEY IDS
EC-388, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
>> GO TO 2.
2.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
EC-388, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
>> GO TO 3.
3.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
EC-390, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement"
.
>> GO TO 4.
4.
PERFORM IDLE AIR VOLUME LEARNING
EC-390, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
>> END
IDLE SPEED
INSPECTION AND ADJUSTMENT
EC-389
< BASIC INSPECTION >
[HR16DE (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
IDLE SPEED : Description
INFOID:0000000001161432
This describes how to check the idle speed. For the actual procedure, follow the instructions in “BASIC
INSPECTION”.
IDLE SPEED : Special Repair Requirement
INFOID:0000000001161433
1.
CHECK IDLE SPEED
With CONSULT-III
Check idle speed in “DATA MONITOR” mode with CONSULT-III.
Without CONSULT-III
Check the idle speed by installing the pulse type tachometer clamp on No.4 ignition coil harness.
>> INSPECTION END
IGNITION TIMING
IGNITION TIMING : Description
INFOID:0000000001161434
This describes how to check the ignition timing. For the actual procedure, follow the instructions in “BASIC
INSPECTION”.
IGNITION TIMING : Special Repair Requirement
INFOID:0000000001161435
1.
CHECK IGNITION TIMING
1.
Attach timing light to No.1 ignition coil wire harness (1) as
shown.
2.
Check ignition timing.
>> INSPECTION END
ACCELERATOR PEDAL RELEASED POSITION LEARNING
ACCELERATOR PEDAL RELEASED POSITION LEARNING : Description
INFOID:0000000001161436
Accelerator Pedal Released Position Learning is a function of ECM to learn the fully released position of the
accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each
time harness connector of accelerator pedal position sensor or ECM is disconnected.
ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Re-
2
: Timing light
: Vehicle front
JMBIA0397ZZ
1
: Timing indicator
MBIB1331E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст