Nissan Tiida C11. Instruction — part 391
EC-214
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P0500 VSS
Always drive vehicle at a safe speed.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
5.
PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to
EC-214, "Component Function Check"
Use component function check to check the overall function of the vehicle speed sensor circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Component Function Check
INFOID:0000000001670977
1.
PERFORM COMPONENT FUNCTION CHECK
With GST
1.
Lift up drive wheels.
2.
Start engine.
3.
Read vehicle speed sensor signal in Service $01 with GST.
The vehicle speed sensor on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000001670978
1.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
Refer to
BRC-25, "CONSULT-III Function (ABS)"
(with ABS) or
BRC-105, "CONSULT-III Function (ABS)"
ESP/TCS/ABS).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace.
2.
CHECK COMBINATION METER
MWI-22, "CONSULT-III Function (METER/M&A)"
.
>> INSPECTION END
ENG SPEED
1,600 - 6,000 rpm
COOLAN TEMP/S
More than 70
°
C (158
°
F)
B/FUEL SCHDL
7.2 - 31.8 msec
Shift lever
Except Neutral position
PW/ST SIGNAL
OFF
P0605 ECM
EC-215
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0605 ECM
Description
INFOID:0000000001670979
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
DTC Logic
INFOID:0000000001670980
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A
1.
Turn ignition switch ON.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 3.
3.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
1.
Wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> GO TO 4.
4.
PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1.
Wait at least 1 second.
2.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
3.
Repeat step 2 for 32 times.
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
A)
ECM calculation function is malfunctioning.
• ECM
B)
ECM EEP-ROM system is malfunctioning.
C)
ECM self shut-off function is malfunctioning.
EC-216
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
P0605 ECM
Diagnosis Procedure
INFOID:0000000001670981
1.
INSPECTION START
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE.
See
With GST
1.
Turn ignition switch ON.
2.
Select Service $04 with GST.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
Is the 1st trip DTC P0605 displayed again?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Go to
EC-25, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-
>> INSPECTION END
P1065 ECM
EC-217
< COMPONENT DIAGNOSIS >
[HR16DE (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1065 ECM
Description
INFOID:0000000001161270
ECM has the memory function of the DTC memory, the air-fuel ratio
feedback compensation value memory, the Idle Air Volume Learning
value memory, etc. even when the ignition switch is turned OFF.
DTC Logic
INFOID:0000000001161271
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 1 second.
2.
Start engine and let it idle for 1 second.
3.
Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.
4.
Repeat steps 2 and 3 for four times.
5.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000001161272
1.
INSPECTION START
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “SELF-DIAG RESULTS” mode with CONSULT-III.
3.
Touch “ERASE”.
4.
Perform DTC CONFIRMATION PROCEDURE.
See
.
With GST
1.
Turn ignition switch ON.
2.
Select Service $04 with GST.
3.
Perform DTC CONFIRMATION PROCEDURE.
See
.
Is the 1st trip DTC P1065 displayed again?
YES
>> GO TO 2.
PBIA9222J
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1065
Engine control module
ECM back-up RAM system does not function
properly.
• ECM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст