Nissan Tiida C11. Instruction — part 262
DLK-458
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
FUEL FILLER LID OPENER
INSTALLATION
Installation is in the reverse order of removal.
FRONT DOOR LOCK
DLK-459
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FRONT DOOR LOCK
Component Parts Location
INFOID:0000000001732026
Removal and Installation
INFOID:0000000001732027
REMOVAL
1.
Remove front door finisher. Refer to
XX-XX, "*****"
.
2.
Fully close front door window.
3.
Remove the front door sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
4.
Remove front door rear glass run channel. Refer to
XX-XX, "*****"
.
5.
Remove the cables from the holder.
6.
Remove inside handle bolt, and slide the handle toward the rear
of the vehicle. disengage the handle from the door panel, and
remove the inside handle.
7.
Disengage the handle from the door panel, and remove the inside handle.
1.
Front door
2.
Inside handle
3.
Inside handle cable
4.
Door lock assembly
5.
Outside handle cable
6.
TORX bolt (T30)
7.
Key cylinder connecting rod
8.
Grommet
9.
TORX bolt (T30)
10. Rear gasket
11. Door key cylinder assembly
(Driver's side)
Outside handle escutcheon
(passenger's side)
12. Outside handle
13. Front gasket
14. Lock knob cable
15. Holder
16. Outside handle bracket
PIIB6523E
PIIB6524E
DLK-460
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
FRONT DOOR LOCK
8.
Disconnect the inside handle cable and lock knob cable from the
inside handle.
CAUTION:
During removal and installation, work so as not to bend the
ends of the lock knob cable and inside handle cable.
9.
Remove the door side grommet, and the door key cylinder
assembly (escutcheon) bolt.
10. Remove the key cylinder connecting rod (key cylinder side).
11. If equipped, disconnect the door antenna, the door request
switch connector and remove the harness clamp. (Vehicle with
intelligent key systems only).
12. Remove the door cylinder assembly while pulling the outside
handle forward.
13. Pull the outside door handle forward and then slide it toward the
rear of the vehicle to remove.
14. Remove the front and rear gaskets.
PIIB6525E
PIIB5808E
PIIB5809E
PIIB5810E
PIIB6526E
FRONT DOOR LOCK
DLK-461
< REMOVAL AND INSTALLATION >
[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
15. Remove the door lock assembly bolts.
16. Slide the outside handle bracket toward the rear of the vehicle,
and remove the assembly.
17. If equipped, disconnect the door lock assembly electrical connector.
18. Separate the outside handle cable from the outside handle
bracket.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• To install each rod, be sure to rotate the rod holder until a click is felt.
• When installing door lock assembly, be careful when rotating the outside handle cable as shown in
the figure.
- Place the outside handle bracket cable on the inside of door
lock assembly before installing.
5.8 N·m (0.6 kg-m, 51.4 in-lb)
PIIB6527E
PIIB6528E
PIIB5815E
PIIB6529E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст