Nissan Tiida C11. Instruction — part 201
DLK-214
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
HOOD
4.
Press the hood lightly with [approx. 29 N (3 kg] of force and adjust A and B as shown.
5.
After adjustment tighten lock bolts to the specified torque.
6.
Install the front grille. Refer to
EXT-19, "Removal and Installation"
.
Removal and Installation
INFOID:0000000001315832
HOOD ASSEMBLY
Removal
1.
Hood striker
2.
Primary latch
3.
Secondary striker
4.
Secondary latch
A
: 20 mm (0.79 in)
B
: 6.8 mm (0.268 in) min.
PIIB5794E
1.
Hood hinge
2.
Hood stay
3.
Radiator core seal rubber
4.
Hood assembly
5.
Hood insulator
6.
Hood stay holder
PIIB2528J
HOOD
DLK-215
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Remove hinge nuts on hood and remove hood assembly.
CAUTION:
Two technicians should be used to avoid damaging the
hood during removal.
Installation
Installation is in the reverse order of removal.
CAUTION:
• Before installing hood hinge, apply anticorrosive agent onto the surfaces that make contact with the
vehicle body.
• After installing, perform hood fitting adjustment. Refer to
.
HOOD HINGE
Removal
1.
Remove hood assembly. Refer to
DLK-214, "Removal and Installation"
2.
Remove front fender. Refer to
DLK-221, "Removal and Installation"
3.
Remove bolts and the hood hinge.
Installation
Installation is in the reverse order of removal.
Removal and Installation of Hood Lock Control
INFOID:0000000001315833
LH Drive
12.7 N·m (1.3 kg-m, 9.4 ft-lb)
PIIB2529J
12.7 N·m (1.3 kg-m, 9.4 ft-lb)
PIIB2530J
PIIB6509E
DLK-216
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
HOOD
RH Drive
REMOVAL
Hood Lock
1.
Remove front grille (LH or RH as necessary). Refer to
EXT-19, "Removal and Installation"
2.
Remove hood lock bolts.
3.
Remove hood lock from hood lock cable.
Hood Lock Reinforcement
1.
Remove front bumper. Refer to
EXT-15, "Removal and Installation - Hatchback"
2.
Remove crash zone sensor.
3.
Remove bolts, and the hood lock reinforcement.
Hood Lock Cable
1.
Remove front grille (LH/RH). Refer to
EXT-19, "Removal and Installation"
2.
Remove fender protector (LH or RH as necessary). Refer to
EXT-22, "Removal and Installation"
3.
Remove hood lock, and remove hood lock cable from hood lock.
4.
Remove radiator core upper support, hood ledge, and then remove hood lock cable.
1.
Hood lock
2.
Hood lock cable
3.
Hood ledge upper front
4.
Clip
ALKIA0638GB
1.
Hood lock
2.
Hood lock cable
3.
Hood ledge upper front
4.
Clip
23.6 N·m (2.4 kg-m, 17 ft-lb)
23.6 N·m (2.4 kg-m, 17 ft-lb)
PIIB6511E
HOOD
DLK-217
< REMOVAL AND INSTALLATION >
[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Remove hood opener on bottom left of instrument panel, and
then remove hood lock cable.
6.
Remove grommet on lower dashboard, and pull out hood lock
cable from passenger room side.
CAUTION:
While pulling the cable, be careful not to damage (peel)
hood opener cable outer surface on edges of body through
hole.
INSTALLATION
Installation is in the reverse order of removal.
• Perform hood fitting adjustment. Refer to
Hood Lock Reinforcement
When installing hood lock reinforcement, loosen hood bolts, and
then tighten bolts in the order as shown.
Hood Lock Cable
1.
Pull the hood lock cable through the panel hole to the engine compartment.
CAUTION:
Be careful not to bend the cable too much, keeping the
radius 100 mm (3.94 in) or more.
2.
Check that the cable is not offset from the positioning grommet,
and push the grommet into the panel hole securely.
3.
Apply the sealant around the grommet (at * mark).
4.
Install cable securely to lock.
5.
After installing, check hood lock adjustment and hood opener
operation.
Hood Lock Control Inspection
INFOID:0000000001315834
CAUTION:
If the hood lock cable is bent or deformed, replace it.
LIIA2667E
23.6 N·m (2.4 kg-m, 17 ft-lb)
PIIB6513E
PIIB5801E
PIIB6537E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст