Nissan Tiida C11. Instruction — part 1232
STR-14
< BASIC INSPECTION >
[MR18DE]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000001728603
OVERALL SEQUENCE
DETAILED FLOW
JPBIA0502GB
DIAGNOSIS AND REPAIR WORKFLOW
STR-15
< BASIC INSPECTION >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
NOTE:
If any malfunction is found, immediately disconnect the battery cable from the negative terminal.
1.
CHECK ENGINE START
Crank the engine and check that the engine starts.
Does the engine start?
YES
>> GO TO 2
NO
>> GO TO 3
2.
CHECK THAT THE STARTER MOTOR STOPS
Check that the starter motor stops after starting the engine.
Does the starter motor stop?
YES
>> INSPECTION END.
NO
>> Replace magnetic switch.
3.
CHECK THE ENGINE SPEED WITH CRANKING
Check that the engine runs at cranking.
Does engine turn by cranking?
YES
>> GO TO 4
NO
>> GO TO 5
4.
CHECK THE ENGINE SPEED WITH CRANKING
Check that the engine speed is not low at cranking.
Does engine turn normally?
YES
>> Check ignition/fuel system.
NO
>> Check charge condition, corrosion and connection condition of the battery. Refer to
XX-XX,
"*****"
.
5.
CHECK STARTER MOTOR ACTIVATION
Check that the starter motor runs at cranking.
Does starter motor turn?
YES
>> GO TO 6
NO
>> GO TO 7
6.
CHECK STARTER MOTOR UNIT
1.
Remove starter motor.
2.
Check that the gear shaft of starter motor rotates.
Does gear shaft turn?
YES
>> • Check pinion clutch. .
NO
>> Check reduction gear, armature and gear shaft.
7.
CHECK POWER SUPPLY CIRCUIT
Check the following conditions.
• Fuse and fusible link
• Charge condition, corrosion and connection condition of the battery. Refer to
.
Are these inspection results normal?
YES
>> GO TO 8
NO
>> Repair as needed.
8.
CHECK STARTING SYSTEM WIRING
Check the following.
• “B” terminal circuit. Refer to
• “S” terminal circuit. Refer to
Are these inspection results normal?
YES
>> GO TO 9
NO
>> Repair as needed.
STR-16
< BASIC INSPECTION >
[MR18DE]
DIAGNOSIS AND REPAIR WORKFLOW
9.
CHECK MAGNETIC SWITCH OPERATION SOUND
Check that a magnetic switch operation sound can be heard when the ignition switch is set at the starting posi-
tion.
Does magnetic switch operation sound occur?
YES
>> GO TO 10
NO
>> Replace magnetic switch.
10.
PINION AND RING GEAR ENGAGEMENT CHECK
Check condition of pinion and ring gear mesh.
Is the inspection result normal?
YES
>> GO TO 12
NO
>> GO TO 11
11.
CHECK STARTER MOTOR UNIT
Check the following.
• Adjust pinion movement.
• Check pinion moving mechanism.
• Check ring gear.
Are these inspection results normal?
YES
>> INSPECTION END
NO
>> Repair or replace, if necessary.
12.
CHECK STARTER MOTOR UNIT
Check that the starter motor runs when connecting the positive ter-
minal (12 V) to starter motor terminal M and the negative terminal
(ground) to starter motor body.
Does the starter motor run?
YES
>> Replace magnetic switch.
NO
>> Repair starter motor.
SEL009Z
STARTING SYSTEM
STR-17
< FUNCTION DIAGNOSIS >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
STR
N
P
O
FUNCTION DIAGNOSIS
STARTING SYSTEM
System Diagram
INFOID:0000000001728563
System Description
INFOID:0000000001728564
The starter motor plunger closes and provides a closed circuit between the battery and the starter motor. The
starter motor is grounded to the cylinder block. With power and ground supplied, the starter motor operates.
Component Parts Location
INFOID:0000000001728565
ALBIA0472GB
1.
Park/Neutral position (PNP) switch
F25
2.
IPDM E/R E44, E45, E46
3.
BCM M18 (view with glove box re-
moved)
ALBIA0474GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст