Nissan Tiida C11. Instruction — part 265
DLK-470
< BASIC INSPECTION >
[WITHOUT I-KEY & SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
1.
GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC for BCM.
2.
Perform the following procedure if DTC is displayed.
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to
DLK-565, "DTC Inspection Priority Chart"
and determine trouble
diagnosis order.
Is DTC detected?
YES
>> GO TO 8.
NO
>> Refer to
XX-XX, "*****"
.
6.
PERFORM BASIC INSPECTION
Perform Basic Inspection, refer to
Inspection End>>GO TO 7.
7.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to Symptom Table based on the confirmed symptom in step 4.
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 9.
DIAGNOSIS AND REPAIR WORKFLOW
DLK-471
< BASIC INSPECTION >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
9.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
10.
FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO
>> INSPECTION END
DLK-472
< BASIC INSPECTION >
[WITHOUT I-KEY & SUPER LOCK]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000001396986
Perform the system initialization when replacing or registering Keyfob and ignition key.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000001396987
Refer to the CONSULT-III Operation Instruction-NATS.
DOOR LOCK FUNCTION
DLK-473
< FUNCTION DIAGNOSIS >
[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
FUNCTION DIAGNOSIS
DOOR LOCK FUNCTION
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : System Diagram
INFOID:0000000001396988
DOOR LOCK AND UNLOCK SWITCH OPERATION
DOOR LOCK AND UNLOCK SWITCH : System Description
INFOID:0000000001396989
DOOR LOCK AND UNLOCK SWITCH OPERATION
Functions are available by operating the door lock and unlock switch on center console. Interlocked with the
lock/unlock operation of door lock and unlock switch, door lock actuators of all doors are locked/unlocked.
Operation Condition
If the following conditions are not satisfied, door lock/unlock operation is not performed even if the door lock
and unlock switch is operated.
NOTE:
When the door lock is locked with keyfob, door lock and unlock switch operation will be invalid until either of
the following conditions is satisfied.
• Turn ignition switch ON.
• Unlock operation by keyfob.
ALKIA0710GB
Door lock and unlock switch
Operation condition
Lock operation
All the following conditions are satisfied.
• Except driver side, doors are closed.
• Doors are not locked with keyfob.
Unlock operation
All the following all conditions are satisfied.
• Doors are not locked with keyfob.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст