Nissan Tiida C11. Instruction — part 1305
REPAIR FOR COMPONENT PARTS
TM-271
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
1.
Install seal rings (1) and D-rings (2) on forward clutch piston (3)
and overrun clutch piston (4).
CAUTION:
Be careful with the direction of seal rings (1).
2.
Install overrun clutch piston on forward clutch piston by turning it
slowly.
CAUTION:
Apply ATF to inner surface of forward clutch piston.
3.
Install forward clutch piston with overrun clutch piston on for-
ward clutch drum by turning it slowly.
CAUTION:
Apply ATF to inner surface of forward clutch drum.
4.
Align notch in forward clutch piston with groove in forward clutch
drum.
5.
Install spring retainer assembly (1) on overrun clutch piston (2).
SCIA6005J
SAT215D
SAT216D
SAT217D
SCIA6019J
TM-272
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
6.
Set Tool on spring retainer assembly, and install snap ring while
compressing spring retainer assembly.
CAUTION:
• Set Tool directly over return springs.
• Do not expand snap ring excessively.
• Do not align snap ring gap with spring retainer assembly
stopper.
7.
Install dish plate (5), driven plates (4), drive plates (3) and retain-
ing plate (2) for overrun clutch.
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Dish plate
Drive plate/Driven plate: 3/4
CAUTION:
Be careful with the order of plates.
8.
Install snap ring for overrun clutch using suitable tool.
9.
Measure clearance between overrun clutch retaining plate and
snap ring using feeler gauge. If not within allowable limit, select
proper retaining plate.
SAT205D
SAT134F
SCIA5993E
SCIA4895E
Specified clearance
Standard and allowable limit:
.
SAT227D
REPAIR FOR COMPONENT PARTS
TM-273
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
10. Install dish plate (5), driven plates (4), drive plates (3) and retain-
ing plate (2) for forward clutch.
(1): Snap ring
(2): Retaining plate
(3): Drive plate
(4): Driven plate
(5): Dish plate
Drive plate/Driven plate: 5/5
CAUTION:
Be careful with the order of plates.
11. Install snap ring for forward clutch using suitable tool.
12. Measure clearance between forward clutch retaining plate and
snap ring using feeler gauge. If not within allowable limit, select
proper retaining plate.
13. Check operation of forward clutch and overrun clutch. Refer to
TM-267, "Forward and Overrun Clutches"
Low & Reverse Brake
INFOID:0000000001730991
COMPONENTS
SCIA5992E
SCIA4894E
Specified clearance
Standard and allowable limit:
.
SAT228D
SCIA6007J
TM-274
< DISASSEMBLY AND ASSEMBLY >
[TYPE 1 (4AT: RE4F03B)]
REPAIR FOR COMPONENT PARTS
DISASSEMBLY
1.
Check operation of low & reverse brake.
a.
Apply compressed air into oil hole of transaxle case at the loca-
tion as shown.
b.
Check to see that retaining plate moves to snap ring.
c.
If retaining plate does not contact snap ring:
• D-ring might be damaged.
• Seal ring might be damaged.
2.
Remove snap ring (1) using suitable tool (A).
3.
Remove retaining plates, drive plates, driven plates, dish plates.
4.
Set Tool on spring retainer assembly, and remove snap ring
from transaxle case while compressing spring retainer assem-
bly.
CAUTION:
Set Tool directly over return springs.
5.
Remove spring retainer assembly from transaxle case.
CAUTION:
Do not remove return springs from spring retainer.
1.
Seal ring
2.
D-ring
3.
Low & reverse brake piston
4.
Spring retainer assembly
5.
Snap ring
6.
Driven plate
7.
Retaining plate
8.
Driven plate
9.
Retaining plate
10. Snap ring
11.
Drive plate
12. Dish plate
SAT230D
SCIA7039E
SAT242D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст