Nissan Tiida C11. Instruction — part 775
EXL-98
< ON-VEHICLE REPAIR >
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Bulb Replacement
INFOID:0000000001530532
HATCHBACK
1.
Remove the license plate lamp. Refer to
INT-35, "Removal and Installation"
.
2.
Turn the bulb socket counterclockwise to unlock it.
3.
Remove the bulb from the socket.
4.
Installation is in the reverse order of removal.
SEDAN
1.
Remove the trunk lid finisher. Refer to
INT-35, "Removal and Installation"
2.
Remove the license plate lamp bulb socket (1) and remove the
license plate lamp bulb (2).
3.
Installation is in the reverse order of removal.
Removal and Installation
INFOID:0000000001530533
HATCHBACK
Removal
1.
Press the license plate lamp pawl on the side of the rear bumper fascia, then swing the license plate lamp
down to release the license plate lamp hook from the rear bumper fascia.
2.
Disconnect the license plate lamp connector and remove the licence plate lamp.
Installation
Installation is in the reverse order of removal.
SEDAN
Removal
PKIC1055E
1.
License plate lamp
A.
Pawl
B.
Hook
LKIA0759E
LICENSE PLATE LAMP
EXL-99
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
Remove the trunk lid finisher. Refer to
EXT-29, "Removal and Installation"
2.
Remove the license plate lamp bulb socket (1).
• License plate lamp bulb (2).
3.
Remove the license plate lamp finisher. Refer to
EXT-29, "Removal and Installation"
4.
Remove the license plate lamp assembly.
Installation
Installation is in the reverse order of removal.
PKIC1055E
EXL-100
< ON-VEHICLE REPAIR >
REAR FOG LAMP
REAR FOG LAMP
Bulb Replacement
INFOID:0000000001530536
1.
Remove the clips for the rear bumper fascia lower side. Refer to
EXT-17, "Removal and Installation -
2.
Disconnect the rear fog lamp connector.
3.
Turn the bulb socket (2) counterclockwise to unlock it.
4.
Remove bulb (1) from the socket.
5.
Installation is in the reverse order of removal.
Removal and Installation
INFOID:0000000001530537
REMOVAL
1.
Remove the rear bumper fascia. Refer to
EXT-17, "Removal and Installation - Sedan"
.
2.
Disconnect the rear fog lamp connector.
3.
Remove the rear fog lamp nuts (A) and remove rear fog lamp
(1).
INSTALLATION
Installation is in the reverse order of removal.
PKIC0948E
PKIC0947E
Rear fog lamp nuts
: 5.1 N·m (0.52 kg-m, 45 in-lb)
LIGHTING & TURN SIGNAL SWITCH
EXL-101
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000001529304
NOTE:
The lighting and turn signal switch is located on the LH side of the steering column for both the LHD and RHD
models.
REMOVAL
1.
Remove the upper and lower steering column covers. Refer to
IP-11, "Removal and Installation"
.
2.
While pressing in on the pawls (A) as shown, pull the lighting
and turn signal switch (1) straight out to disconnect from the
base and remove.
NOTE:
LHD shown, RHD similar.
INSTALLATION
Installation is in the reverse order of removal.
PKIC1018E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст