Nissan Tiida C11. Instruction — part 712
EM-200
< ON-VEHICLE REPAIR >
[MR18DE]
CYLINDER HEAD
: Engine front
CAUTION:
Check and confirm the tightening angle by using Tool (A) or
protractor. Never judge by visual inspection without the
tool.
4.
Installation of the remaining components is in the reverse order of removal.
Component
INFOID:0000000001337806
Disassembly and Assembly
INFOID:0000000001337807
DISASSEMBLY
Tool number
: KV10112100 (BT-8653-A)
PBIC3208J
1.
Valve collet
2.
Valve spring retainer
3.
Valve spring (EXH)
(with valve spring seat)
4.
Valve oil seal
5.
Valve guide (EXH)
6.
Valve seat (EXH)
7.
Valve (EXH)
8.
Valve (INT)
9.
Valve seat (INT)
10. Cylinder head
11. Valve guide (INT)
12. Spark plug
13.
Valve spring (INT)
(with valve spring seat)
A.
B.
Refer to
PBIC3543J
CYLINDER HEAD
EM-201
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
1.
Remove spark plug using suitable tool.
2.
Remove valve lifter.
• Identify installation positions, and store them without mixing them up.
3.
Remove valve collet.
• Compress valve spring using Tool, attachment and adapter
(A). Remove valve collet using a suitable magnet hand.
CAUTION:
When working, be careful not to damage valve lifter holes.
4.
Remove valve spring retainer and valve spring (with valve spring seat).
CAUTION:
Never remove valve spring seat from valve spring.
5.
Push valve stem to combustion chamber side, and remove valve.
NOTE:
Identify installed positions, and store them without mixing them up.
6.
Remove valve oil seal using Tool (A).
7.
When valve seat must be replaced, refer to
EM-202, "Inspection After Disassembly"
to removal.
8.
When valve guide must be replaced, refer to
EM-202, "Inspection After Disassembly"
to removal.
ASSEMBLY
1.
Install valve guide if removed. Refer to
EM-202, "Inspection After Disassembly"
.
2.
Install valve seat if removed. Refer to
EM-202, "Inspection After Disassembly"
.
3.
Install valve oil seal.
• Install with a valve oil seal using Tool (A) to match dimension
as shown.
NOTE:
Dimension “H” is height that measured before installing valve
spring (with valve spring seat).
4.
Install valve.
• Install larger diameter to intake side.
Tool number
: KV101092S0 (J-26336-B)
PBIC3209J
Tool number
: KV10107902 (J-38959)
PBIC3210J
Tool number
: KV10115600 (J-38958)
Height “H”
: 15.1 - 15.7 mm (0.594 - 0.618 in)
PBIC3211J
EM-202
< ON-VEHICLE REPAIR >
[MR18DE]
CYLINDER HEAD
5.
Install valve spring (with valve spring seat).
• Install smaller pitch (valve spring seat side) to cylinder head
side (B).
• Confirm identification color (A) of valve spring.
6.
Install valve spring retainer.
7.
Install valve collet.
• Compress valve spring using Tool (A). Install valve collet with a magnet hand.
CAUTION:
When working, be careful not to damage valve lifter holes.
• Tap valve stem edge lightly with a plastic hammer after instal-
lation to check its installed condition.
8.
Install valve lifter.
• Install it in the original position.
9.
Install spark plug using suitable tool.
Inspection After Disassembly
INFOID:0000000001337808
VALVE DIMENSIONS
• Check dimensions of each valve. For dimensions, refer to
• If dimensions are out of the standard, replace valve.
VALVE GUIDE CLEARANCE
Valve Stem Diameter
Measure the diameter of valve stem with a micrometer (A).
Valve Guide Inner Diameter
Measure the inner diameter of valve guide with a bore gauge.
Valve Guide Clearance
(Valve guide clearance) = (Valve guide inner diameter) – (Valve stem diameter).
1
: Valve spring seat (Do not remove from valve spring.)
Intake
: White
Exhaust
: Orange
PBIC3462J
Tool number
: KV101092S0 (J-26336 B)
PBIC3209J
Standard
Intake
: 5.465 - 5.480 mm (0.2152 - 0.2157 in)
Exhaust
: 5.455 - 5.470 mm (0.2148 - 0.2154 in)
PBIC3213J
Standard
: 5.500 - 5.518 mm (0.2165 - 0.2172 in)
CYLINDER HEAD
EM-203
< ON-VEHICLE REPAIR >
[MR18DE]
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• If it exceeds the limit, replace valve guide and/or valve.
VALVE GUIDE REPLACEMENT
When valve guide is removed, replace with oversized [0.2 mm (0.008 in)] valve guide.
1.
To remove valve guide, heat cylinder head to 110
°
to 130
°
C
(230
°
to 266
°
F) by soaking in heated oil (A).
2.
Drive out valve guide using suitable tools.
CAUTION:
Cylinder head contains heat, when working, wear protective
equipment to avoid getting burned.
3.
Ream cylinder head valve guide hole using suitable tool (A).
Valve guide clearance:
Standard
Intake
: 0.020 - 0.053 mm (0.0008 - 0.0021 in)
Exhaust
: 0.030 - 0.063 mm (0.0012 - 0.0025 in)
Limit
: 0.1 mm (0.004 in)
PBIC3214J
SEM931C
Valve guide hole diameter (for service parts):
: 9.675 - 9.696 mm (0.3809 - 0.3817 in)
PBIC3215J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст