Nissan Tiida C11. Instruction — part 1060
LU-30
< ON-VEHICLE REPAIR >
[K9K]
OIL COOLER
OIL COOLER
Exploded View
INFOID:0000000001381543
Removal and Installation
INFOID:0000000001381544
CAUTION:
• Be careful not to get burned when the engine and engine oil are hot.
• When removing, prepare a shop cloth to absorb any oil leakage or spillage.
• Completely wipe off any oil that adhere to the engine and the vehicle.
REMOVAL
1.
Remove engine undercover using power tool.
2.
Drain engine coolant. Refer to
CAUTION:
Perform when engine is cold.
3.
Remove RH front wheel. Refer to
.
4.
Remove RH fender protector. Refer to
EXT-22, "Removal and Installation"
5.
Remove drive belt. Refer to
EM-263, "Removal and Installation"
6.
Remove generator and position aside. Refer to
CHG-43, "Removal and Installation"
.
7.
Remove A/C compressor and position aside. Refer to
HA-35, "Removal and Installation of Compressor -
.
8.
Remove oil filter and oil filter bracket. Refer to
.
1.
Cylinder block
2.
Water pipe
3.
O-ring
4.
O-ring
5.
O-ring
6.
Oil cooler
7.
Connecting stud
8.
O-ring
9.
Oil filter bracket
10. Oil pressure switch
11.
Oil filter
12. O-ring
13. Connecting bolt
A.
To radiator lower hose
B.
To water pump
E1BIA0011GB
OIL COOLER
LU-31
< ON-VEHICLE REPAIR >
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
9.
Disconnect oil pressure switch electrical connector.
10. Remove the oil cooler connecting stud.
11. Remove oil cooler.
INSTALLATION
Installation is in the reverse order of removal.
• Replace the O-ring of the oil cooler, positioning the lip of the seal behind the lug of the oil cooler.
• Confirm that no foreign objects are adhering to the seal contact areas of the oil cooler and cylinder block.
Inspection
INFOID:0000000001381545
INSPECTION AFTER REMOVAL
Check oil cooler for cracks and clogging by blowing through coolant inlet. If necessary, replace oil cooler
assembly.
LU-32
< ON-VEHICLE REPAIR >
[K9K]
OIL PUMP
OIL PUMP
Exploded View
INFOID:0000000001381546
Removal and Installation
INFOID:0000000001381547
REMOVAL
1.
Remove the battery negative cable.
2.
Remove the engine undercover.
3.
Remove the RH front wheel and tire. Refer to
.
4.
Remove RH fender protector. Refer to
EXT-22, "Removal and Installation"
5.
Remove front driveshaft assembly RH. Refer to
FAX-11, "Removal and Installation (Right Side)"
.
6.
Remove driveshaft center bearing bracket.
7.
Remove lower torque rod. Refer to
8.
Remove oil pan. Refer to
EM-284, "Removal and Installation"
.
9.
Remove oil pump drive chain.
10. Remove oil pump assembly.
INSTALLATION
Installation is in the reverse order of removal.
1.
Oil pump drive chain
2.
Crankshaft sprocket (oil pump drive
chain)
3.
Oil pump
E1BIA0028GB
SERVICE DATA AND SPECIFICATIONS (SDS)
LU-33
< SERVICE DATA AND SPECIFICATIONS (SDS)
[K9K]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000001381548
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: ·(Imp
qt)
Engine Oil Pressure
INFOID:0000000001381549
kPa (bar, kg/cm
2
, psi)
With oil filter change
4.55 (4)
Without oil filter change
4.39 (3-7/8)
Dry engine (overhaul)
4.71 (4-1/8)
Engine speed
Approximate discharge pressure
Idle speed
120 (1.2, 1.22, 17.4)
3,000 rpm
350 (3.5, 5.57, 50.8)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст